• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Tapping after oil flush

  • Thread starter Thread starter dallenx
  • Start date Start date Apr 20, 2006

dallenx

New Member
Feb 12, 2006
36
0
0
Oregon
Apr 20, 2006
#1
  • Apr 20, 2006
  • #1
Posting here as well as 2.3 forum, hoping you guys & girls can help. thanks

I picked up an '89 LX this weekend and since there were no service records, I took it home to start a tuneup.
I put about 150mi on the car before the tuneup and had no problems but low oil pressure (got lower the more I pressed the throttle and would come back up when I let off).

Oil maintenance:
1) I flushed the engine then drained it.
2) Put on a Fram High Mileage filter.
2) Put in Slick50 High Mileage additive.
3) Put in Castrol High Mileage 10w-30.

Ignition maintenance:
1) New dist cap
2) New rotor.
3) New Napa Belden Max wires.
4) New Autolite plugs

Start the engine up with no problems.
After about 60sec a tapping starts to develop.
Sounds like it's coming from around #3cyl.
Tapping goes away / or least quites down with increased RPMs.
Shut the engine off and start right back up.
Tap comes back in about 5sec now.
Left the car over night......
Start up next day and no noise for first 30sec.

Oil pressure is now in the middle of the 'normal' range at idle (hangs around the letter 'm').
Drive the car and the oil pressure drops a little but now the pressure increases slightly back to around the letter 'M' when accelerating instead of dropping to 'L' like before.

What gives?
 

TheBocSez

New Member
Feb 3, 2004
652
0
0
Converse, TX
Apr 20, 2006
#2
  • Apr 20, 2006
  • #2
Could be several things. Of course low oil pressure can be associated with excessive bearing clearances. With a high milage motor, could be that.

Could also be that the the oil pump pick up screen is clogged. This could have caused the dropping oil pressure with RPM initially. Maybe when you added the engine flush, it clean it out some which allows the oil pressure to rise again with RPM.

The oil flush may have also cleaned out the sludge in the lifters and now the one tapping is just bleeding down too fast causing the tapping.
 
You must log in or register to reply here.

Similar threads

K
Introduction 05 mustang gt
  • kingcoy
  • Jun 6, 2025
  • The Welcome Wagon
Replies
0
Views
101
The Welcome Wagon Jun 6, 2025
kingcoy
K
M
Engine 1988 Foxbody - Overheating Summer
  • MDrisc
  • Oct 26, 2025
  • Fox 5.0 Mustang Tech
Replies
10
Views
486
Fox 5.0 Mustang Tech Nov 28, 2025
Mustang5L5
A
Resolved 1989 Mustang bogs down after 3-5 minutes of driving.
  • Alabama
  • Feb 11, 2025
  • Fox 5.0 Mustang Tech
  • 2
Replies
23
Views
1K
Fox 5.0 Mustang Tech May 26, 2025
limp
B
'03 GT Fuel Pump/Pressure/Delivery Issue
  • Brodach
  • Oct 21, 2025
  • SN95 4.6L Mustang Tech
Replies
8
Views
824
SN95 4.6L Mustang Tech Oct 31, 2025
gkomo
A
Rough idle - cylinder 1 and 6 misfire HELP
  • austindavies935
  • Jul 24, 2025
  • SN95 4.6L Mustang Tech
Replies
12
Views
636
SN95 4.6L Mustang Tech Jul 24, 2025
gkomo
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?