• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

taurus wiring question...

  • Thread starter Thread starter jmd2914
  • Start date Start date Jun 15, 2006
J

jmd2914

Founding Member
Sep 6, 2002
937
0
0
Napa, California
Jun 15, 2006
#1
  • Jun 15, 2006
  • #1
alright, just got back from the junkyard and got my taurus fan and wiring harness. i think its out of a sable though. anyway. how can i test this fan before i put it in the car? and anyone have a wiring diagram? the simpler the better, i suck and electronics. im just wiring it to a relay and a switch. thanks.

Joel
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Jun 15, 2006
#2
  • Jun 15, 2006
  • #2
If it's two speeds, the outside terminals are likely the ground and high speed. I'd put a FUSED 12 volt wire from the battery on one terminal and ground the other (this is how you test fans at the J/Y). If the fan spins, cool. If it spins the wrong way (pushing air), swap the wires. You really cant screw it up (unless you short a couple terminals together).

Good luck.
 
J

jmd2914

Founding Member
Sep 6, 2002
937
0
0
Napa, California
Jun 15, 2006
#3
  • Jun 15, 2006
  • #3
ok cool, anyone happen to have a wiring diagram for wiring the fan to an on/off switch with a relay and no a/c
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Jun 15, 2006
#4
  • Jun 15, 2006
  • #4
jmd2914 said:
ok cool, anyone happen to have a wiring diagram for wiring the fan to an on/off switch with a relay and no a/c
Click to expand...
Here's one article. If you dont want to use a controller, omit it and wire the relay directly (I'd recommend that your switch sends ground to the [control side of] the relay).

Good luck.
 
J

jmd2914

Founding Member
Sep 6, 2002
937
0
0
Napa, California
Jun 15, 2006
#5
  • Jun 15, 2006
  • #5
thanks for the link to the write up, does anyone have a list of everything i will need to do the swap? right now all i have is the fan and about a foot of the stock harness.
 
J

jmd2914

Founding Member
Sep 6, 2002
937
0
0
Napa, California
Jun 16, 2006
#6
  • Jun 16, 2006
  • #6
one more question, do i have to run the diode from the posetive to ground wires on the fan motor?
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Jun 17, 2006
#7
  • Jun 17, 2006
  • #7
jmd2914 said:
one more question, do i have to run the diode from the posetive to ground wires on the fan motor?
Click to expand...
It's a good idea. When a fan is shut off, it continues to spin. And while doing so, it goes from being a fan to a generator, and in this latter stage it can create a rather large voltage spike. The diode kills the spike before it goes back to your relay (the spike can shorten the life of the relay).

Good luck.
 
J

jmd2914

Founding Member
Sep 6, 2002
937
0
0
Napa, California
Jun 17, 2006
#8
  • Jun 17, 2006
  • #8
alright i got a diode that has pn 1n5404. anyone know if this one will work?
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Jun 17, 2006
#9
  • Jun 17, 2006
  • #9
jmd2914 said:
alright i got a diode that has pn 1n5404. anyone know if this one will work?
Click to expand...
It seems to me that this will work well.
 
J

jmd2914

Founding Member
Sep 6, 2002
937
0
0
Napa, California
Jun 17, 2006
#10
  • Jun 17, 2006
  • #10
ok cool, thanks for checking that for me. what website did you check that on? just so i have a ref. for it
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Jun 17, 2006
#11
  • Jun 17, 2006
  • #11
IIRC, it's the same freewheeling diode that M. Smith recommends on his mark 8 fan article.

EDIT: pulled it up for you:
http://www.geocities.com/smithmonte/Auto/MarkVIII_Fan.htm
 
J

jmd2914

Founding Member
Sep 6, 2002
937
0
0
Napa, California
Jun 17, 2006
#12
  • Jun 17, 2006
  • #12
i tried the link it said it was unavailable. the diode i have is pn 1n5404 not 1n5408 which is why i was wondering if it was going to work or not.
 
You must log in or register to reply here.

Similar threads

C
Electrical HELP! 1989 5.0 Stick, Voltage Bleed onto Ignition Trigger wire
  • ChickenDeluxe
  • May 14, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
406
Fox 5.0 Mustang Tech May 24, 2026
ChickenDeluxe
C
G
Resolved Smoking Wiring Issue After GT40 Head Swap
  • Grapes
  • Aug 15, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
606
Fox 5.0 Mustang Tech Aug 22, 2026
Grapes
G
Electrical 91 hatch wiring help needed
  • FastDriver
  • Apr 7, 2026
  • Fox 5.0 Mustang Tech
Replies
2
Views
276
Fox 5.0 Mustang Tech Apr 8, 2026
FastDriver
Electrical/engine bay harness questions
  • djj62478
  • May 29, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
7
Views
482
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 6, 2026
djj62478
Resolved Holley terminator integration into CCRM
  • BrandonMP
  • Feb 25, 2026
  • SN95 4.6L Mustang Tech
Replies
8
Views
619
SN95 4.6L Mustang Tech Aug 23, 2026
fasterthangas
F
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?