• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 1994 - 1995 Specific Tech

The never ending oil leak...Advice?

  • Thread starter Thread starter Venom351R
  • Start date Start date Aug 12, 2010
  • 1
  • 2
Next
1 of 2 Next Last

Venom351R

Founding Member
Apr 27, 2002
4,548
41
98
MAINE
Aug 12, 2010
#1
  • Aug 12, 2010
  • #1
My TFSR intake was leaking ever since It was put on the car. I finally got fed up with it and replaced it with a Victor 5.8. The car has not been driven much with this new intake on until tues when I got it back from having the clutch installed. Since tuesday Ive put 335 miles on it breaking in the clutch and today I smelled what I thought was burning oil. When I got home I stuck it in the garage and after about 30 mins there was two oil spots on the floor. One was about the size of a half dollar and the other the size of a quarter.

The leak is not as bad as it was before but its the fact that its still leaking and its coming from the exact same spot as when the TFSR was on it. The TFSR was redone 4 times and leaked after everytime and now the Victor is leaking although not nearly as much. What can be causing this issue? Its obviously not the intake its self. Its leaking on the very back corner of the passenger side.
 

Adam95GT

New Member
Aug 14, 2006
2,564
3
0
Burlington, NJ
Aug 12, 2010
#2
  • Aug 12, 2010
  • #2
Possible bad surface on the head or block???
 

Venom351R

Founding Member
Apr 27, 2002
4,548
41
98
MAINE
Aug 12, 2010
#3
  • Aug 12, 2010
  • #3
It never leaked w/ the Cobra intake that came on the car when I bought it. Ever since then Ive had lower intake leaking issues. The surface of the heads were spotless when the lower was installed again. Scraped them clean with a razor blade and went over it numerous times with Acetone




 

Attachments

  • 36448_1466978547766_1032606063_1356718_6888349_n.webp
    85.8 KB · Views: 256

Adam95GT

New Member
Aug 14, 2006
2,564
3
0
Burlington, NJ
Aug 12, 2010
#4
  • Aug 12, 2010
  • #4
Are you using a wall of RTV on the back of the block instead of a gasket?
 

revhead347

Apparently my ex-husband made that mistake.
20+ Year Stangneter
Jun 14, 2004
9,301
1,643
214
Acworth, GA
Aug 12, 2010
#5
  • Aug 12, 2010
  • #5
Check for valve cover leaks too. Valve cover leaks are sneaky, and can appear like other leaks.

Kurt
 

Venom351R

Founding Member
Apr 27, 2002
4,548
41
98
MAINE
Aug 13, 2010
#6
  • Aug 13, 2010
  • #6
using a big black bead of RVT. I dont think its the Valve covers bc I can reach back where the RVT is on the back of the intake and feel oil there. Unless its moving over from the valve cover to the corner of the intake
 

revhead347

Apparently my ex-husband made that mistake.
20+ Year Stangneter
Jun 14, 2004
9,301
1,643
214
Acworth, GA
Aug 13, 2010
#7
  • Aug 13, 2010
  • #7
Yeah, usually if you just use RTV, and no gasket it leaks. At least in my experience.

Kurt
 

Venom351R

Founding Member
Apr 27, 2002
4,548
41
98
MAINE
Aug 13, 2010
#8
  • Aug 13, 2010
  • #8
I checked the valve covers on both sides, both had loose bolts and I tightned them up but I dont really think its coming from there. Under the bead of RVT you can see and feel oil on the block.

Do you think it should be redone w/ a gasket and RVT?
 

revhead347

Apparently my ex-husband made that mistake.
20+ Year Stangneter
Jun 14, 2004
9,301
1,643
214
Acworth, GA
Aug 13, 2010
#9
  • Aug 13, 2010
  • #9
Yeah, I would redo it with gaskets under there. Make sure you get the original style rubber gaskets though, not the cheapy cork ones.

Kurt
 

95Vert383AOD

15 Year Member
Jun 10, 2008
1,133
34
69
New Bedford, MA
Aug 13, 2010
#10
  • Aug 13, 2010
  • #10
Hmmmm

This has worked for me EVERY single time.

Use the front and rear gaskets, Apply sealer to both sides. Use liberal amount in the corners. go threw torque sequence a million times. This means after first torquing everything to 14lbs...start at the 1st bolt and repeat sequence till all are at 14. (guarantee the 1st bolt is loose again) then 20, then 25. Then let it sit before starting at least overnight.

Also make sure you're properly venting the crank case. Blocked PCV builds pressure and the gases will rip right threw that rear seal.


Added: Also lightly Sand the metal on the front and rear areas of the intake and block. It will help the sealer stick.

Chris
 

revhead347

Apparently my ex-husband made that mistake.
20+ Year Stangneter
Jun 14, 2004
9,301
1,643
214
Acworth, GA
Aug 13, 2010
#11
  • Aug 13, 2010
  • #11
I do basically the same method. However, I never torque the intake down. I just go hand tight with a 1/4" ratchet. Torquing the intake can cause the heads to lift.

Kurt
 

Venom351R

Founding Member
Apr 27, 2002
4,548
41
98
MAINE
Aug 13, 2010
#12
  • Aug 13, 2010
  • #12
The block has been scuffed on both ends so the RVT should be biting well on it. I dont know if I'll bother to redo it soon or not. Depends on my track times b/c If I decide to get bigger heads then Im going to tear it all down anyway and no point in redoing it now, then taking everything all off again at the end of oct.

I re did the valve cover bolts, all are tight now and I put some extra RVT along the bead that is on the back of the intake. Maybe it will at least slow it down some, like I said its not leaking like it did before but its still leaking.

Also there is no PCV with this intake.
 

Adam95GT

New Member
Aug 14, 2006
2,564
3
0
Burlington, NJ
Aug 13, 2010
#13
  • Aug 13, 2010
  • #13
Venom351R said:
The block has been scuffed on both ends so the RVT should be biting well on it. I dont know if I'll bother to redo it soon or not. Depends on my track times b/c If I decide to get bigger heads then Im going to tear it all down anyway and no point in redoing it now, then taking everything all off again at the end of oct.

I re did the valve cover bolts, all are tight now and I put some extra RVT along the bead that is on the back of the intake. Maybe it will at least slow it down some, like I said its not leaking like it did before but its still leaking.

Also there is no PCV with this intake.
Click to expand...



I wouldn't pull it off... just keep an eye on it and make sure its not dripping down to your clutch/flywheel
 

Grn92LX

Fidanza Man!
Founding Member
Jan 14, 2001
6,819
64
129
New York
Aug 13, 2010
#14
  • Aug 13, 2010
  • #14
what are you using for crankcase ventilation? It is possible your ventilation isn't enough and causing a leak like mention in this thread. Do not use a gasket and rtv. RTV alone is enough. I am sure you did the install correctly. Once you reach the final torque spec (20-22ft/lbs with lube on the threads) you need to keep going over every bolt until the wrench just clicks.

Fwiw, I was using 2 breather filters off each valve cover fill tube (tfs covers/tube) and they leaked badly so I ended up running 5/8" hose off each fill tube to a vented breather tank.

It is also possible that your loose valve cover bolts were the problem or the gasket is bad.
 

Venom351R

Founding Member
Apr 27, 2002
4,548
41
98
MAINE
Aug 13, 2010
#15
  • Aug 13, 2010
  • #15
It was still leaking after the minor tweaks on the valve covers and the extra RVT on the back.

Im running two open breathers for ventilation. The intake bolts appear to be nice and tight, I checked the ones in the back. Is it possible for the valve covers to leak and for it to make its way up behind the intake and on the top of the block so that it looks like the lower intake is leaking out through the RVT?
 

Grn92LX

Fidanza Man!
Founding Member
Jan 14, 2001
6,819
64
129
New York
Aug 13, 2010
#16
  • Aug 13, 2010
  • #16
Its possible the v.c's/gaskets are the problem. You should see a trail though if it were and you'd feel oil around them. Your ventilation is fine. Do your breathers leak? I wasn't able to even go 1 mile on my car before the breathers were oil soaked and leaking onto the header
 

Venom351R

Founding Member
Apr 27, 2002
4,548
41
98
MAINE
Aug 13, 2010
#17
  • Aug 13, 2010
  • #17
both breathers seem fine as far as blowing any oil out and I have not noticed any oil around the VC's at all
 

BlackVert

15 Year Member
Oct 3, 2003
5,589
9
98
Bethesda, MD
Aug 13, 2010
#18
  • Aug 13, 2010
  • #18
not to be picky or anything but it is RTV, not RVT. just saying.

i have a small leak at the front of mine. it is done with just RTV too. i cleaned it up and smeared some more on it and it is better, but still leaks a little. i am planning an upgrade to a victor junior, so i am going to leave it like that for now. when i do the upgrade, i intend to use rubber gaskets like what kurt mentioned
 

Venom351R

Founding Member
Apr 27, 2002
4,548
41
98
MAINE
Aug 14, 2010
#19
  • Aug 14, 2010
  • #19
let me know how yours turns out b/c Im going to be trying that next just not sure when
 

MysteryMachine

Active Member
Jun 21, 2003
1,835
2
39
Parkesburg, PA
Aug 18, 2010
#20
  • Aug 18, 2010
  • #20
Wow your still having issues with that. Did you notice any performance difference with the vic?
 
  • 1
  • 2
Next
1 of 2 Next Last
You must log in or register to reply here.

Similar threads

N
Edelbrock 1405 Setup
  • nathantaylor200
  • Nov 4, 2025
  • Classic Mustang Specific Tech
Replies
3
Views
243
Classic Mustang Specific Tech Nov 5, 2025
nathantaylor200
N
C
C4 trans help needed
  • CPH89LX
  • Apr 26, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
6
Views
212
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Apr 28, 2026
CPH89LX
C
O
Sooty/Oily Front Engine & Pulleys
  • ozenator
  • Jun 15, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
12
Views
285
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 22, 2026
Blackhawkxx
B
Engine Strange Noise
  • burntokita
  • May 8, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
399
Fox 5.0 Mustang Tech May 11, 2026
keel
2
Electrical mayhem
  • 2000ElectricGreen
  • Mar 13, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
2
Views
276
1996 - 2004 SN95 Mustang -General/Talk- Mar 24, 2026
2000ElectricGreen
2
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 1994 - 1995 Specific Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?