thinking I want to upgrade to this dash piece, how does it fit??

old_blue

15 Year Member

Nov 3, 2003

1,783

282

124

Nov 18, 2006

#1

• Nov 18, 2006

• #1

View attachment 423161

does this piece cover the fuse panel??? it is extended on the left side more than the piece I have but I have seen them before and they make the dash pieces in that area go together easier. anyone of any pictures of there dash under the steering column that I could reference from??

 

old_blue

15 Year Member

Nov 3, 2003

1,783

282

124

Nov 18, 2006

#2

• Nov 18, 2006

• #2

another pic
View attachment 423159

i blv 90-93 came with them

 

rednotch

I'd like to remain having one chocolate starfish

Founding Member

Aug 14, 2000

1,387

621

143

south jersey

Nov 18, 2006

#3

• Nov 18, 2006

• #3

3 bottem bolts to the dash frame, upper bolts to the lower side of the cluster.... it won;t fit an 89 below dash.

 

trbkrb

Founding Member

Jun 4, 2001

1,976

4

39

Houston, TX

Nov 18, 2006

#4

• Nov 18, 2006

• #4

That is the knee pad and metal bracing for it from a 90-93 dash. The fuse panel is relocated to under the dash in those cars. I replaced my 87 dash with a 90 dash and just used the plastic cover, not the metal part, so I could install my fuse panel in the stock 87 location. I just pop the plastic panel off to check the fuses. It is held in place by the three push in clips. Here is a pic of my fuse box:
http://statefilingsoftware.com/pictures/fusebox1.jpg

 

Mustang5L5

That is…until I whipped out my Bissell

Mod Dude

Feb 18, 2001

43,260

17,945

224

Massachusetts

Nov 18, 2006

#5

• Nov 18, 2006

• #5

Yeah, it's part of the 90-93 dash

I installed a 90-93 black dash in my '88...but i didn't use this particular metal peice. I only used the exterior plastic cover for it.

 

old_blue

15 Year Member

Nov 3, 2003

1,783

282

124

Nov 19, 2006

#6

• Nov 19, 2006

• #6

ok, I am getting one then , the other pieces fit like crap in my car

 

Mustang5L5

That is…until I whipped out my Bissell

Mod Dude

Feb 18, 2001

43,260

17,945

224

Massachusetts

Nov 19, 2006

#7

• Nov 19, 2006

• #7

Then you need an entire 90-93 dash, center console and HVAC controls.

I'm not even entirely sure that metal peice bolts up to the 87-89 dash frame. If not, you would need to swap the dash frame as well.


Why do you want that particular peice for??

 

trents99

Founding Member

Jun 28, 2002

438

0

0

Hampton, GA

Nov 19, 2006

#8

• Nov 19, 2006

• #8

Like mentioned that metal back plate will not fit an 87-89 dash without some hacking. It would bolt to the spot where the 87-89 fuse panel is so that would have to be moved for one and even then I'm not sure about it fitting physically.

Why the fascination with just that piece?

 

old_blue

15 Year Member

Nov 3, 2003

1,783

282

124

Nov 20, 2006

#9

• Nov 20, 2006

• #9

for some reason when I did my swap from 4cyl those pieces don't want to go back in. it was all taken apart anyways when I got it. But it look ssimple enough to put back together but one piece especially doesn't fit at all and it just broke a tab off. it looks like a half circle and it is ribbed, and has tabs to fit into the lower dash with screws on either side

 

MikeC

Founding Member

Aug 1, 2002

240

0

16

SLC, UT

Nov 20, 2006

#10

• Nov 20, 2006

• #10

I was told it's on the air bag cars to keep you from sliding under the air bag in a crash. I guess you smash your knees into it but you stay in your seat.