I'm outside installing the timing chain that came with my Trick Flow H/C/I kit. It's part number 78520T whcih I believe is a Dynaroll billet set.
In the kit it states that the bronze bearing that is included with the set requires that you countersink the thrustplate bolt holts so that the supplied screws will sit slightly below the service of the thrust plate.
I compared the old timing set to the new timing set and it appears that I have to use the bronze bearing and make these modifications. The thing is, every person I had talked to about doing this install had never mentioned having to do this, so I'm questioning if I really have to use the bronze bearing or not?
In the kit it states that the bronze bearing that is included with the set requires that you countersink the thrustplate bolt holts so that the supplied screws will sit slightly below the service of the thrust plate.
I compared the old timing set to the new timing set and it appears that I have to use the bronze bearing and make these modifications. The thing is, every person I had talked to about doing this install had never mentioned having to do this, so I'm questioning if I really have to use the bronze bearing or not?
Does anybody know this, lol. Im out doing the same thing right now. I just opend up my timming chain kit. It came with two allen bolts and the bushing. Unlike you I have no paper work with my timming chain. I would like to know the answer to this as well. I put everything together without those two allen screws and all seems good. Whats the deal with those. By the way, what size hole saw do you use for the filler tube for the trick flow valve covers?
I haven't even tried to put my timing gear on yet as I don't want to ruin the bronze washer when torquing down cam retainer nut to check clearances.
I'm assuming you put the timing gear on without the bronze washer and used the stock bolts? How much play are you getting between the thrust plate and the cam?
I'm also wondering what size hole to drill for the oil filler tube. If I can't find an answer to the timing gear question by tom. morning I'm going to call Trick Flow and find out. I'll ask about the filler tube also and let you know.
I'm assuming you put the timing gear on without the bronze washer and used the stock bolts? How much play are you getting between the thrust plate and the cam?
I'm also wondering what size hole to drill for the oil filler tube. If I can't find an answer to the timing gear question by tom. morning I'm going to call Trick Flow and find out. I'll ask about the filler tube also and let you know.
Ok, I just did something I should've done ealier today. I took the thrust plate off and mocked the fitment up with the bronze washer and new timing gear.
As far as I can tell there is no problem with running the bronze washer with the stock bolts. It does fit sort of close to the bolts on the thrust plate, but it appears there is plenty of room to allow for correct operation.
I'm still going to call Trick Flow tommorow to verify since I haven't put mine on yet, I'll let ya know!
I have the timming gear on with the washer and the stock thrust plate bolts and mine cleared too. I havent put on the front bolt that holds that gear on the came. I still have that bolt at work. I didnt expect my timming set to come in on saturday. If you call trick flow I would really like to know as well. Out of all these people on hear that has done this kit Im surpised no one has responded. Anyways if you dont mind me asking what all are you having done. Are you rebuilding the bottem end too or what. Sounds like we are in about the same spot. I would really like to know how it comes out for you. You can shoot me an email at bkrjohn@hotmail.com or just post back on here. Good luck, hope to hear back.
Just called Trick Flow..
They said you can use a 1 1/8" Hole Saw to cut the valve cover for the oil filter neck. That should be big enough to insert the grommet and the filler neck.
As far as having to countersink the thrust plate bolts for the timing gear set, they had never heard of having to do that. The guy did say they had received a new shipment of timing gear sets from dynaroll last month and they might have changed they're instructions. So as far as that goes, I think we're go to go without drilling into the thrust plate
I was kinda surprised no-one on here had responded either. My kit was purchased a month ago though, so maybe I'm one of the first people to get the timing gear set with those instructions I'm not doing a rebuild or anything on the block. It only had 60K on it and has seen nothing but synthetic oil and 2000 mile services (I'm obsessed). Compression tests came back + or - 1 PSI across all the cylinders so the block seems almost as good as stock. As far as the parts go, I'm installing the Trickflow Street Heat H/C/I setup (with 3/8" spacer), BBK 1 5/8 Longtube Headers, BBK Off-road x-pipe, 255LPH Walboro pump, New Water Pump (of course), and underdrive pulleys. It's a cobra so it already has the 24lb injectors, and I also have the mod's in my signature to go with the install. I also went ahead and cleaned/slightly enlarged the port entrys on the upper and lower intake with a die grinder, and gasket matched the whole kit. I also cleaned up the exhaust ports on the longtubes since there was a good amount of weld splatter on the inside. I was thinking about getting a AFPR, but since I will be getting it dyno tuned, and will be purchasing a tweecer (or an AFM unit if I can get the money) in the next month or so, I'm holding off on that.
I'm at the point now where I should have everything together by this Sunday. Once I get her running and worn in (500-1000 miles) I'm going to get the king cobra clutch put in (I hate pulling tranny's without a lift) and take it down to the dyno for a tune. I'll def. keep you updated with my progress and any tips that I might "discover" as I finish the install.
What all you planning on doing to yours with the TF H/C/I? I've heard some good numbers with these kits, hopefully it'll hold true!
They said you can use a 1 1/8" Hole Saw to cut the valve cover for the oil filter neck. That should be big enough to insert the grommet and the filler neck.
As far as having to countersink the thrust plate bolts for the timing gear set, they had never heard of having to do that. The guy did say they had received a new shipment of timing gear sets from dynaroll last month and they might have changed they're instructions. So as far as that goes, I think we're go to go without drilling into the thrust plate
I was kinda surprised no-one on here had responded either. My kit was purchased a month ago though, so maybe I'm one of the first people to get the timing gear set with those instructions
I'm at the point now where I should have everything together by this Sunday. Once I get her running and worn in (500-1000 miles) I'm going to get the king cobra clutch put in (I hate pulling tranny's without a lift) and take it down to the dyno for a tune. I'll def. keep you updated with my progress and any tips that I might "discover" as I finish the install.
What all you planning on doing to yours with the TF H/C/I? I've heard some good numbers with these kits, hopefully it'll hold true!
Hey thanks for that info. I have a 90 mustang that has about 135k on it. Ported e7 heads, ported lower intake, trick flow stage 1 cam, new valve springs and pretty much every thing else stock. About 3 months ago, I floated my valves and I had an exhaust valve brake off, put a huge hole in my piston and cracked my block, lol. Opps. Kinda glad it happend, gave me a good reason to start over. I found a good used block and crank, had it bord .030 good set of I-beam rods, 9.5 pistons and had the rotating assm. balanced. Im using the trick flow kit but just the street heat intake. 75mm t/b, 30lb injectors, 7 quart oil pan with windage try. Ya i know I kinda went a little over bored with the 75mm t/b and 30lb injectors but I wanted room to grow incase I wanted to do more. I plan on getting a dyno tune as well. Already had bbk shorty headers, h-pipe and king cobra clutch so I will use that agin. I just got my bottem end together and ready for my heads and intake to go on so I can drop it in. It will be about another month or so before I get mine going. I need to save up some more money, lol. Im sure you know how that is. Feakin money pit but we love it. Im putting an electric fan with a 3g alt. Anyways thats a little about mine. keep me posted on yours, I would like to know how yours turns out. If you have any pics send them my way Good luck, take care.
Similar threads
- Replies
- 3
- Views
- 566
- Replies
- 6
- Views
- 492
- Replies
- 2
- Views
- 533
- Replies
- 1
- Views
- 168
- Replies
- 6
- Views
- 491