TPS - stock

Paul Perreca

New Member
Mar 30, 2005
1,085
0
0
Many of you know I am having Idling and Bucking problems, even when i drive normal, if i'm keeping it in a gear, it slightly just jerks until i give it a little mor gas -

My plan - I think i wll replace the TPS sensor that came w/ my PP 70 MM throttlebody with the STOCK one - do you think i can take the stock one off my stock TB and put it on this one and it will idle a little better - or at least allow me to adjust the idle? and maybe even fix that stupid bucking

Paul Perreca
 
and what is the stock fuel pressure set at, do i need to adjust this w/ my setup? I used an aftermarket adjustable FPR, and supposedly it came out of the box set at STOCK SPECS - so i'm guessing that's where it's at - I wanna try n tune this thing just a little bit today - I wish a had a FP guage
 
I doubt its the tps, as long as its set right. I dont no if i would ajust the fp without a fp gauge, i have the same exact problem too, wheres ur timing at? and i forget did u do ur mass air conversion before u put ur new motor in or during ur motor swap. If u figure this out please tell me and ill do the same.
 
Paul - put a digital volt meter across the black and green wires of the tps. With the engine warm, not running, ignition on, and the throttle closed, the tps reading should be somewhere in the .90-.95V range. Slowly open the throttle and the voltage should smoothly increase up into the 4.5-5.0V range. If that occurs - the tps is fine. Diagnose -- don't just start changing parts.

Have you pulled the diagnostic codes? That's the place to start. Let the computer help tell you what the problem might be.

Set the fuel pressure stock - there's no reason to alter it. At warm idle, with the vacuum line off the regulator and plugged (just for measurement purposes -- hook it back up when you're done) you ought to have 38-39 psig.

What's your ignition timing set at? I forget your mods -- but if you've modded the motor - especially cam - it's probably gonna want more advance -- set it up around 14-18 btdc if it will take it without detonation.
 
yea - i did the mass air conversion while doing the motor swap - it does do it cold or warm, doesn't go away - i will be checking the voltage across the green and black wires- now if it is not at .90 or in that range, do i have to take out the screws, drill the holes out a little bigger and than put it back in and adjust the angle of the sensor until it hits that range? My mechanic told me that is what to do - i was able to move the TPS sensor a C-hair, n i havn't started it up since then, but how much of a move on it will make a differnece? I think i'll be getting the code reader from the autozone - do i plug the code reader into the plug in the middle of the engine bay that is open? I have never used one before -

The reason i said i was gonna put in the stock TPS is because DMAN said he has the same Pro Products TB and when he was adjusting his, it was WAY off - and caused problems - I gotta get this in check - cuz i opened it up and when i hit second the car spun wheels like a mother, than it started bucking n i got scared that it was hurting something cuz it bucked really bad -

Paul Perreca

thnx again
 
You'll just have to play with the tps with the voltmeter hooked up -- you'll see what it does. Ignore the stuff about setting it close to .99V -- it takes a baseline reading everytime you start the car. Set it around .90-.95V.

On my car (91 or 92 Stang motor) there is a grey plug that's part of the harness behind the driver's side strut. It says D I A G N O S T I C on the plastic cover -- that's a pretty big hint which one to plug into.
 
Paul Perreca said:
I think i'll be getting the code reader from the autozone - do i plug the code reader into the plug in the middle of the engine bay that is open? I have never used one before -

Paul, before you go out and spend those $30.00 or what ever the reader costs now search for JRICHKER's post on pulling codes. It's so simple that you will be mad you wasted that money on the code reader.

Behind the Drivers strut / next to the hood hinge should be (2) loose connectors. One should only have one terminal and the other should look like a trapazoid with a few terminals and empty holes. You just take a 2" piece of wire and bridge the 1 terminal connector with the other and your car will spit out the codes on the Check engine light. Write them down and then go back to the site JRICHKER links. It'll take less than 5 minutes to do all of the testing.
 
srothfuss said:
You just take a 2" piece of wire and bridge the 1 terminal connector with the other and your car will spit out the codes on the Check engine light. Write them down and then go back to the site JRICHKER links. It'll take less than 5 minutes to do all of the testing.
As a quick reminder, since his car was originally SD from the sound of it, he will need to use a test light or analog voltmeter - the CEL should not be functional unless he wired it to be.

Good luck.
 
yea i read Jrichkers post on that - i'll be doing it as soon as matco gets me my new voltmeter - i know its more expensive from there, but i like the guy that sells me the tools, and i have an account lol