• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

tranny cooler line ?

  • Thread starter Thread starter sgarlic
  • Start date Start date Nov 15, 2004

sgarlic

Founding Member
Apr 21, 2001
3,085
1
56
Nov 15, 2004
#1
  • Nov 15, 2004
  • #1
Hi guys, I'm replacing my radiator, and it's a new job to me so forgive the lamenes of this question. This is an 88 GT w/ AOD we're talking about.

After replacing my radiator I plugged the tranny cooler lines back in to the new one, started it, and it slowly dripped fluid from the bottom line. It leaks worse as I loosen or tighten, and it leaks from where the line becomes the nut portion.

I didn't replace any fittings or anything.. and to be honest I'm baffled as to where the fittings are. My new radiator included 2 gold colored fittings that have some sort of nut in the middle, however there were no fittings like this in my old radiator, and nowhere on the line itself is there anything that looks close to this.

For info, when I originally removed it, I used one wrench, loosened the nut all the way and it the whole line with the threaded part came out.

I'm wondering, is the reason I'm leaking because I loosened the wrong thing? And where in the heck are those fittings supposed to go??
 
N

nocaryet

New Member
Apr 23, 2004
12
0
0
Nov 15, 2004
#2
  • Nov 15, 2004
  • #2
If you replaced your rad with an aluminum one, your problem sounds like exactly what happened to me. I ended up cross threading the fitting on the fragile aluminum and ended up stripping it. I just got an external B & M tranny cooler, and had no problems since.
 

sgarlic

Founding Member
Apr 21, 2001
3,085
1
56
Nov 15, 2004
#3
  • Nov 15, 2004
  • #3
Sorry I should've specified.. it wasn't an aluminum replacement, just a stock replacement from radiatorbarn.. my other one took a crap due to a huge rock hitting it while driving.
 

The Shape

Founding Member
Jan 11, 2002
2,224
8
49
East ARKANSAS Delta
Nov 15, 2004
#4
  • Nov 15, 2004
  • #4
I think the fittings you are talking about that came with the radiator probably were meant to be used if you were using rubber hose for the cooler lines and won't be used for your application. I would bet your leaking because the little white plastic piece inside the fitting on your factory line is worn out. The piece that is threaded that goes into the radiator is just a fitting that snaps on the line, I had to replace mine when I changed my radiator for the same reason. If you take a small pair of needle nose pliers and pull back on the little white plastic piece the whole fitting should pop off the line. It takes a little patience just take your time working with the plasctic piece and the fitting will come off.

Then just take the fitting to the parts store and get a new one. It will simply pop on the end of the line. The plastic inside those gets brittle after a while and when you move them they begin to leak. The new fitting should solve your problem. Good luck
 

sgarlic

Founding Member
Apr 21, 2001
3,085
1
56
Nov 15, 2004
#5
  • Nov 15, 2004
  • #5
Here's the fitting:



Here's what I'm looking at. I understand what you're saying but I don't have a white plastic piece that you're talking about when I take the line off.
 

The Shape

Founding Member
Jan 11, 2002
2,224
8
49
East ARKANSAS Delta
Nov 15, 2004
#6
  • Nov 15, 2004
  • #6
The plastic piece I mean is under that lump of J.B Weld in you last picture. Was that already on there are were you trying to seal it. Right where the line goes into the nut part of the fitting there are two little plastic tabs sticking out you squeeze them together and the fitting pops off the line. But you will have to get all of that J.B weld off of there to get at them. The fitting in your top picture looks like some sort of adaptor you shouldn't need it at all.
 

sgarlic

Founding Member
Apr 21, 2001
3,085
1
56
Nov 15, 2004
#7
  • Nov 15, 2004
  • #7
That stuff is just RTV.. I put that on there to try to keep that fluid from leaking out while I ran the vehicle/filled the radiator. There aren't any white plastic pieces underneath them though. Hrmph maybe my car is just completely screwed!
 

The Shape

Founding Member
Jan 11, 2002
2,224
8
49
East ARKANSAS Delta
Nov 15, 2004
#8
  • Nov 15, 2004
  • #8
Sorry looked like good old J.B. in the pic. But the pieces I mean are just little tabs that stick out they are laying flat against the rim of that fitting. You might even go to the parts store and ask for a ford quick disconnect tranny line fitting. When you get a clean new one in your hand you will see what I mean.
 

sgarlic

Founding Member
Apr 21, 2001
3,085
1
56
Nov 16, 2004
#9
  • Nov 16, 2004
  • #9
Thanks for the help! I managed to pry those plastic pieces out using a pocket knife, then purchased 2 new fittings from AutoZone for 15 bucks. Fit right in, no more leaks.
 

The Shape

Founding Member
Jan 11, 2002
2,224
8
49
East ARKANSAS Delta
Nov 16, 2004
#10
  • Nov 16, 2004
  • #10
Cool man sorry I was having such a hard time describing what to look for, but sounds like you got it taken care of.
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Nov 16, 2004
#11
  • Nov 16, 2004
  • #11
nice job, TS. i did not know there were those dealies in the lines.

SG, wanted to say hi to a fellow Tucsonan.
 
You must log in or register to reply here.

Similar threads

I
2000 GT Mustang - Transmission Cooler to Radiator o-rings
  • Iwarrior
  • Oct 4, 2025
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
0
Views
216
1996 - 2004 SN95 Mustang -General/Talk- Oct 4, 2025
Iwarrior
I
S
Oil cooler delete 4v 4.6 1999 cobra mustang
  • sami12
  • Feb 24, 2026
  • SN95 4.6L Mustang Tech
Replies
5
Views
492
SN95 4.6L Mustang Tech Feb 25, 2026
GOvert
G
J
Exhaust manifold to Y-pipe nut & stud dimensions?
  • joeybuddy96
  • Jul 7, 2026
  • SN95 V6 Mustang Tech
Replies
2
Views
222
SN95 V6 Mustang Tech Jul 9, 2026
joeybuddy96
J
A
Blow through intercooled questions
  • AngryH58
  • Aug 31, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
5
Views
293
1996 - 2004 SN95 Mustang -General/Talk- Sep 1, 2026
AngryH58
A
K
86 GT Water Pump
  • Kade5114
  • May 11, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
3
Views
228
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- May 11, 2026
nickyb
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?