• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

trouble pulling codes, help?

  • Thread starter Thread starter Randy Kemper
  • Start date Start date Oct 20, 2005
R

Randy Kemper

Founding Member
Apr 22, 2000
102
0
0
Oct 20, 2005
#1
  • Oct 20, 2005
  • #1
I've got the connectors jumped and I'm running a test light from the battery to the other pin on the connector. When I turn on the key after a few seconds the light comes on and stays on. no blicks or anything. I'm sure I've connected everything right. Is there something I'm overlooking? Or is this a sign of something serious wrong with my computer. My cars not running right, right now, it's dumping gas, getting about 2 miles a gal. and won't stay running below 3k. Any help would be appreciated. Thanks
 
T

twindragons187

New Member
Nov 10, 2003
39
0
0
pa, ny
Oct 20, 2005
#2
  • Oct 20, 2005
  • #2
what year is ur car? instead of jumping wire's, u can go to ur local walmart and get a code reader for bout 20 bucks. its not the best but it works for simple codes.
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Oct 20, 2005
#3
  • Oct 20, 2005
  • #3
Just in case you missed something in hooking things up...

Here's the link to dump the computer codes with only a jumper wire or paper clip and the check engine light, or test light or voltmeter. I’ve used it for years, and it works great.

See http://www.troublecodes.net/Ford/
OR
See http://www.mustangworks.com/articles/electronics/eec-iv_codes.html

IF your car is an 86-88 stang, you'll have to use the test lamp or voltmeter method. There is no functional check engine light on the 86-88's except possibly the Cali Mass Air cars.

Codes have different answers if the engine is running from the answers that it has when the engine isn't running. It helps a lot to know if you had the engine running when you ran the test.

Trouble codes are either 2 digit or 3 digit, there are no cars that use both 2 digit codes and 3 digit codes.

For those who are intimidated by all the wires & connections, see http://www.actron.com/product_detail.php?pid=16153 for what a typical hand scanner looks like. Normal retail price is about $30 or so at AutoZone or Walmart.

Or for a nicer scanner see http://www.midwayautosupply.com/detailedproductdescription.asp?3829 – It has a 3 digit LCD display so that you don’t have to count flashes or beeps.. Cost is $35.
 
R

Randy Kemper

Founding Member
Apr 22, 2000
102
0
0
Oct 20, 2005
#4
  • Oct 20, 2005
  • #4
jrichker, I actually double checked my connections using one of your links before I posed the question. Thanks. I've got an 86 gt, was running a koeo test, or trying to. I was using the test light. I've always used the voltmeter method before and never had any problems. But I seem to have misplaced it.
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Oct 21, 2005
#5
  • Oct 21, 2005
  • #5
If you get a code 67 while running key on engine off tests, the key on, engine on test will not run.

Code 67 - clutch not depressed (5 speed) or car not in neutral or park (auto) or A/C in On position when codes where dumped. Possible neutral safety switch or wiring problem. This code may prevent you from running the Key On Engine On tests. You can generally ignore this code, since it has no effect on engine performance.
 
R

Randy Kemper

Founding Member
Apr 22, 2000
102
0
0
Oct 21, 2005
#6
  • Oct 21, 2005
  • #6
That's the thing, I'm not getting any codes. The test light just comes on and stays on. I also don't hear any clicks or anything like it's testing sensors.
 
M

mattfleming

New Member
Mar 22, 2004
33
0
0
Jan 8, 2006
#7
  • Jan 8, 2006
  • #7
I too, am having this problem. Listening in!

The voltimeter swings wide open, all the time... constant 12v power. (i think it was 12v.. i don't remember.. but it was voltage)
 

joel5.0

Member
Jun 15, 2004
429
2
18
Puerto Rico
Jan 8, 2006
#8
  • Jan 8, 2006
  • #8
You would have to do a check of the 5vdc VREF supply at the TPS connector, TPS disconnected, first. You would, unfortunately, have to get your misplaced voltmeter or,....could you borrow one from a friend? LUK
 
You must log in or register to reply here.

Similar threads

Electrical Code 29 again
  • Creomod
  • Jul 31, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
392
Fox 5.0 Mustang Tech Aug 3, 2026
Creomod
M
Fox Random spike voltage (Need help from scope users)
  • martroy
  • Sep 28, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
20
Views
519
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Oct 27, 2026
martroy
M
T
Electrical Brown Connector #31
  • ta66
  • Jul 26, 2026
  • Fox 5.0 Mustang Tech
Replies
2
Views
219
Fox 5.0 Mustang Tech Jul 30, 2026
ta66
T
C
Electrical HELP! 1989 5.0 Stick, Voltage Bleed onto Ignition Trigger wire
  • ChickenDeluxe
  • May 14, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
405
Fox 5.0 Mustang Tech May 24, 2026
ChickenDeluxe
C
1
Electrical 1985 mustang gt Led conversion trouble
  • 1985fox
  • Jan 5, 2026
  • Fox 5.0 Mustang Tech
Replies
10
Views
848
Fox 5.0 Mustang Tech Jan 15, 2026
1985fox
1
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?