• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Twin Turbo Notch

  • Thread starter Thread starter whtnotch
  • Start date Start date Jan 16, 2008
W

whtnotch

New Member
Jan 8, 2007
123
0
0
Chicago
Jan 16, 2008
#1
  • Jan 16, 2008
  • #1
I have a 89 Notch. I'v read a bit about turbos on here and people are saying not to go with an e-bay twin turbo.why?I don't see anything wrong with it. A dude I met up with on Archer ave has a single setup he purchased off e-bay,and his car is fu*in tits. Also how would I hook exhaust up off turbos without welding to H-pipe.Is there a kit?or all has to be fabed up?injector size?fuel pump size?anything else to watch out for.

thanks alot
 

BK_CAULEY

it's built for speed not longevity, woman
Dec 26, 2006
0
10
49
Thomasville, ga
Jan 16, 2008
#2
  • Jan 16, 2008
  • #2
Thats exactly why you dont buy ebay turbo kits. any reputable company would work with you on setting up your turbo kit.

take a look over on www.turbomustangs.com they will more than likely be able to help you better understand "why" better than us.

but the main reason not to buy an ebay turbo setup is because its crap. the turbos are more than likely used/ cleaned up turbos which will fail. the intercoolers re ot efficiant and the hot side parts are not made of acceptable materials and the welds are doomed to fail
 
W

whtnotch

New Member
Jan 8, 2007
123
0
0
Chicago
Jan 16, 2008
#3
  • Jan 16, 2008
  • #3
Man this is budget build. They can't be total "crap"I seen one used and it was runnin smoothly and next to my car it riped it up with his being bone stock plus "e-bay turbo" and upped injectors,I know about the site they want 2k+ for their turbo setups I might as well buy a charger for that price.Anyone buy e-bay turbo setup.I'm not talkin bout the intercooler welds.i'll most lilkley blow bottom end before blowin up the turbos.
 

65ShelbyClone

Founding Member
Sep 9, 2000
4,675
38
119
Antelope Valley, SoCal
Jan 17, 2008
#4
  • Jan 17, 2008
  • #4
As was already alluded to, the Ebay cheap turbos are a crapshoot. Some people get them and they work, many others get them and they come apart in short order.

If this is a "budget" build, can afford to buy the turbos twice?
 

millhouse

Founding Member
May 14, 2002
1,985
0
46
Simpsonville, SC
Jan 17, 2008
#5
  • Jan 17, 2008
  • #5
whtnotch said:
Man this is budget build. They can't be total "crap"I seen one used and it was runnin smoothly and next to my car it riped it up with his being bone stock plus "e-bay turbo" and upped injectors,I know about the site they want 2k+ for their turbo setups I might as well buy a charger for that price.Anyone buy e-bay turbo setup.I'm not talkin bout the intercooler welds.i'll most lilkley blow bottom end before blowin up the turbos.
Click to expand...

If you want to do a budget build, your going to have to do some major fabrication yourself…there is no way around it. The cheap e-bay kit's typically use thin walled steel for their headers which will burn through in short order…and their quality is suspect at best. They typically do not fit very well at all…especially the full kit's. From what I've seen, many will require you to re-route their setups as they were not setup on a jig properly. They also seem to include undersized intercoolers which

You need to keep in mind that the quality control on a turbo is ABSOLUTELY CRITICAL. Blowing one up is not a matter of pushing it to hard…but rather running it on a day to day basis. These things commonly spin well in excess of 100k rpm…and any flaws in the oiling system, compressor/turbine balance and housing imperfections can cause a catastrophic failure.

If you are complaining about the costs….I dare you to find an intercooled supercharger setup that includes headers for anywhere near $3k (B&G and Quicktime have kit's for under). Let's not forget either that the cheaper superchargers are not capable of supporting anywhere near the levels that the lower end B&G kit's can.

If you want cheap…I suggest you fabricate everything yourself. Take your stock headers and flip them upside down and go to town and invest in a set of turbocoupe .60/.63 or .60/.48 turbos. There are plenty of builds on turbomustangs.com which do just that….and it can be done on an extreme budget. Hell, my initial build cost around $2k and including B&G headers, a Pro-M univer MAF and 42lb injectors.
 
You must log in or register to reply here.

Similar threads

D
Loud noise(s) from Engine Bay
  • DuluthFoxbody
  • Oct 25, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
14
Views
375
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Nov 5, 2026
AeroCoupe
Resolved 93 Mustang 5.0 - Cranks but does not start
  • dan50
  • Jul 18, 2026
  • Fox 5.0 Mustang Tech
Replies
6
Views
485
Fox 5.0 Mustang Tech Jul 18, 2026
dan50
S
5.0 Rebuild
  • smittys7up
  • Nov 29, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
14
Views
1K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 16, 2026
keel
S
  • Locked
Drivetrain Adjustable clutch cable questions
  • Scott_S
  • Oct 31, 2025
  • Fox 5.0 Mustang Tech
Replies
6
Views
551
Fox 5.0 Mustang Tech Oct 31, 2025
Noobz347
P
1989 turbo fox with microsquirt
  • patsmustang1
  • Aug 14, 2024
  • Digital Self-tuning Forum
Replies
1
Views
528
Digital Self-tuning Forum Aug 14, 2024
90sickfox
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?