• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

ugh more headswap

  • Thread starter Thread starter 93GTosu
  • Start date Start date Mar 11, 2007

93GTosu

Member
May 5, 2005
183
0
19
Mar 11, 2007
#1
  • Mar 11, 2007
  • #1
well im STILL putting my P heads on...working a few hours when im home for the weekend. I'm getting the gaskets cleaned off and wow...does it ever really come "clean?" i mean there isnt any gasket left anywhere, just a very thin film that seems to come up in places i already went over.

also, lets say someone "accidentally" rotated the motor a little while the distributor was pulled. this would completely defeat the purpose of me marking it before i pulled it right?? so how would i go about putting it back correctly? (talk me through this ok?) TDC is when the #1 piston is at its highest right? and thats also when the rotor on the distributor points at #1? so could i just put the #1 piston at the top and then drop the distributor in pointing at #1? then i'd either be 180* off or right on right? and THEN set the timing once i get the car started and running ok??

dont be afraid to tell me i'm dumb as hell just as long as i put it together correctly
 

Aryan15

Member
Sep 22, 2003
236
0
17
CA
Mar 11, 2007
#2
  • Mar 11, 2007
  • #2
You'll want to get it all off the block, down to bare metal. Your timing procedure also sounds correct. Make sure you know which is cyl. #1, I think its the passenger side front and your firing order.
 

kpack5982

Yeah, it was pretty stiff, but eventually a buddy
Jul 13, 2005
325
1
19
Granger, IA
Mar 11, 2007
#3
  • Mar 11, 2007
  • #3
you're in luck, I just got done getting my car running and had the same issues. You'll have to adjust the rockers anyways, so don't worry about where the distributor needs to line up for the time being. Just go about the correct rocker install procedure then intake ect before you put the distributor back in.

The procedure I went with was to keep all the spark plugs out, then crank the motor over until I felt compression in the #1 cylinder with my finger in it. (The first time I confused suction for air pushing out, so distributor was 180 off.) But you can stick a wire in the spark plug hole and verify the piston is up. Then check the balancer fand make sure the timing mark points to 0 degrees and then you're at top dead center. From here you can stab the distributor in any position you want, as long as it's pointing to where the #1 spark plug wire is when you install it or thereabouts. If the car does't start, theres a good chance you're 180 off and just restab. God knows it took me like 20 times to find out how stupid I was to begin with.

That gasket material is a b**** to get off. Don't skimp on it, as much as it is a pita, it should all come off to bare metal. Carb cleaner and a good terry cloth with a little pressure help to dissolve some of the gunk off too.

Good luck
 
You must log in or register to reply here.

Similar threads

J
Suspension Foxbody mustang Steering shaft issue
  • Jakub2537
  • Sep 5, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
347
Fox 5.0 Mustang Tech Sep 11, 2026
gkomo
Resolved 93 Mustang 5.0 - Cranks but does not start
  • dan50
  • Jul 18, 2026
  • Fox 5.0 Mustang Tech
Replies
6
Views
503
Fox 5.0 Mustang Tech Jul 18, 2026
dan50
G
Resolved Smoking Wiring Issue After GT40 Head Swap
  • Grapes
  • Aug 15, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
607
Fox 5.0 Mustang Tech Aug 22, 2026
Grapes
G
T
Drivetrain TREMEC TKX 1–2 Grinding Issue at ~4,000 Miles + Poor Warranty/Customer Service Experience
  • Ttopfoxguy
  • Oct 10, 2026
  • Fox 5.0 Mustang Tech
Replies
5
Views
343
Fox 5.0 Mustang Tech Oct 15, 2026
JMG9350
J
L
Help with 1986 GT 5 Speed Please
  • Lcasada1999
  • Mar 20, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
7
Views
402
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 21, 2026
CAMTWO1070
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?