Undercoating My Car

dbdragracing

Member
Dec 1, 2004
397
2
18
I have a 1989 Mustang GT that Im going through hoping to make my dream Fox body. I have it gutted inside and was checking out the floor boards....it is solid as a rock except for one small place about 1inch x 1inch (where a door seal was leaking). Can I just cut this out a little bigger and patch it or should I do a whole floor pan? Also what type of metal would I need to patch it?

After I get the rust fixed I planned on taking a wire wheel and knocking off all the light surface rust under the car and undercoating it. What type of undercoating do you suggest? POR15? It is very hot here now and it should dry quick. I dont drive the car in the winter or rain. Should undercoating it keep it from rusting? Thanks.
 
Is Crazy Pete the dude who put all the grease up under his car? I would just like to patch the one small bad spot and spray some type of undercoating under it. Anyone have any suggestions? Thanks.
 
dbdragracing said:
Is Crazy Pete the dude who put all the grease up under his car? I would just like to patch the one small bad spot and spray some type of undercoating under it. Anyone have any suggestions? Thanks.


crazypete lol that was a huge thread. Krown is really good stuff it has a creeping agent in it and moves into all the small places most undercoating can't.....I took mine to an Oil Gaurd and had a no drip syrayed on mine and I am verry happy with it.
 
I have just recently spent much attention to the underside of my car. I went to a local speedshop that primarily restores older model vettes. The guy that does all the body work there told me to use epoxy primer (black). It comes in several colors but black is most desirable for this application. He told me that it is the only paint that he has found that will stand up to almost anything. He has all the frames he does sent off to have them acid dipped. They are soaked in acid for 72 hours, then cleaned and sent back to him. He recently sent one off that he had done work on previously for a local car owner. He had previously replaced a cross-member on the frame of the car that had some decent rust eating away at it and after welding the steel in place, he sprayed it with the epoxy primer to keep it from rusting as it was fresh metal. When the owner of the car later decided he would have the car restored, he took it back to this same speedshop and when it came back from being acid dipped, the cross-member that was previously put in and sprayed, was still just as coated as the day it was sent off. I am also a believer because I have dripped brake fluid in a small spot since I sparyed my car and it did not even budge the primer at all. I know you are thinking primer for a final and only coat, but it works and looks great! It is a semi-flat finish just as you would suspect to see on the chassis of a car. If this is something you are interested in, I can tell you more and get you a number on the primer. Most may say it seems unreasonable, but it sure looks good and will last.
 
Fox_84,

I would love more info on the epoxy primer. Did you apply it using a spray gun?

I would also like to hear some stuff about POR15. As far as the floorboards....can I just cut out the small area and patch it? What type of metal do I use? Thanks.
 
If the rust patch is small and will not be visible (under carpet/ door sill etc.) then buy some epoxy resin and fiberglass cloth. A small hole will likely not be structural (there are all kinds of holes in the body) so you really only need to keep it from rusting further.
I used the above method on a football sized hole on a 55 Chevy floorpan and it was as strong/sound after 4 years as the first day. You just have to get all the rust off and clean it thoroughly with acetone for it to stick.
It also sounds like you might benefit from a sound deadening material in addition to the other work.
 
I tried POR-15 on my rear-end and I preped that thing like noone's business. I hated it. The paint itself is nice but it turns green and when you use the topcoat to keep it from turning green, that chassisblack is CRAP!!! you might do that then topcoat with something else, but their topcoats are weak.

As for the epoxy primer, it is not cheap AT ALL!!!
For 1 quart and the catalyst for it, you will spend 80-$100.
The primer is PPG dp90
The catalyst is dp401lf
And yes I sprayed them through a automotive spary gun on a air compressor.

Some people like POR-15 but prep is critical

The epoxy primer I guarantee you will only need a good hosing down with a non oil based engine degreaser, a little scrubbing in thick grease areas and just get it down to the original paint surface, not down to metal bullcrap.
This stuff sticks GREAT!