• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Valve guide/seal help, please

  • Thread starter Thread starter 87_stang
  • Start date Start date Dec 30, 2005

87_stang

Member
Dec 12, 2005
131
0
16
Tonganoxie, KS
Dec 30, 2005
#1
  • Dec 30, 2005
  • #1
I have an 87 5.0 GT and I tore down the motor last year and put new rings and bearings in it. I also took apart the heads. I had a book (chiltons) and it didn't explain very well how to put in the valve guides and seals and I didn't pay attention to how I took them out. If anyone can help me with this it would be very appreciated. I also need to know how to exactly tighten down my valve springs. Thanks in advance for any help.
Also, I know its my own fault for not paying attention when taking them apart, I had a book so I just figured it would explain everything. Thanks again
 

87_stang

Member
Dec 12, 2005
131
0
16
Tonganoxie, KS
Dec 31, 2005
#2
  • Dec 31, 2005
  • #2
ttt
 

Zero_chance

Founding Member
May 29, 2001
1,244
7
59
Maricopa, AZ
Dec 31, 2005
#3
  • Dec 31, 2005
  • #3
Are you saying you took the valve guides out because theyre part of the head casting on stock heads. As for putting the seals on the guides, the way I do it is lube the inside of the guide with white lithium and then put the valve in. Then lube the inside of the stem seal where the valve stem actually moves up and down with white lith and lightly push it onto the valve stem. To get it seated on the guide, its best if you have something round that fits around the valve and is just big enough to cover the seal so you can push it on evenly. It really isnt hard, just take your time and be clean. Then the valve stem guide seals will hold the valves in place for you while you put the springs and keepers back on. If you already have the engine apart I recommend changing the lower intake seals as well if you didnt already. Between that and the valve seals, my car burns less than a half quart between changes.
 

Rick 91GT

Mustang Master
Nov 29, 1999
9,692
95
99
PA
Dec 31, 2005
#4
  • Dec 31, 2005
  • #4
You removed the guides? This has to have the head heated and the guides pressed out, then new ones installed. Most machine shops will but new guides in for about $100 including the guides.

I have a seal installer but you can also use a deep socket 12mm in many cases, lube the valve as mentioned above to prevent any damage to the seal. As fas as assembling the head, you should check the installed height then go from there. If you need more put shims in, put the spring on, put the retainer on, use a valve spring compressor to compress it, and isntall the locks. Check all pressure, clearances, etc..and your good.

If you have never done this and do not have the tools, take it to a local machine shop. Most will set that all up for less the $100 for a stock style set-up.
 
You must log in or register to reply here.

Similar threads

C
C4 trans help needed
  • CPH89LX
  • Apr 26, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
6
Views
345
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Apr 28, 2026
CPH89LX
C
S
New misfire after replacing valve seals/springs.
  • SpeedofDarkness
  • Aug 24, 2025
  • SN95 V6 Mustang Tech
Replies
0
Views
319
SN95 V6 Mustang Tech Aug 24, 2025
SpeedofDarkness
S
B
Help! Fox with idle issues
  • bbarton
  • Sep 11, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
7
Views
304
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 12, 2026
AeroCoupe
A
Resolved 302 oil leak when running
  • AlexM556
  • Sep 8, 2026
  • Classic Mustang Specific Tech
  • 2
Replies
36
Views
1K
Classic Mustang Specific Tech Nov 1, 2026
manicmechanic007
L
Help with 1986 GT 5 Speed Please
  • Lcasada1999
  • Mar 20, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
7
Views
391
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 21, 2026
CAMTWO1070
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?