• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

valve lash adjsutment

  • Thread starter Thread starter Shurb125
  • Start date Start date Mar 9, 2008
S

Shurb125

New Member
Feb 8, 2008
9
0
0
South Carolina
Mar 9, 2008
#1
  • Mar 9, 2008
  • #1
Yesterday I finally got time to readjust the valve lash, I started with cylinder #1 and followed these directions:

1. Turn the motor over till the exhaust valve just starts to open
2. Adjust the intake valve on that cylinder
3. Turn the motor over till the intake valve starts to close
4. Adjust the exhaust valve

I backed off the adjusting nut and let the lifter and pushrod sit with no pressure for about two minutes and then start to tighten the adjusting nut while turning the pushrod and once I felt a slight resistance then from there I turned the adjusting nut 1/4 turn. I did all the valves this way, then started the car and it sounded terrible so I quickly turned it off, checked the oil and it was about a quart low so topped of the oil started it back up and still didn't sound good, then tried it a couple more times and then it quitend down. Now the thorttle respose is much different and it sounds different but a good different. Was the reason for the initial noisey start up is that the lifters had build up oil pressure to tighten up the lifter and pushrod? Thanks for all your help!
 

BK_CAULEY

it's built for speed not longevity, woman
Dec 26, 2006
0
10
49
Thomasville, ga
Mar 9, 2008
#2
  • Mar 9, 2008
  • #2
here is a thread where i was asking a similar question. you might can find some answers in it. i was asking alot of questions

http://forums.stangnet.com/showthread.php?t=728761
 
You must log in or register to reply here.

Similar threads

J
Engine Stalling
  • josh40tay
  • Oct 20, 2026
  • Fox 5.0 Mustang Tech
Replies
4
Views
200
Fox 5.0 Mustang Tech Oct 21, 2026
JD1964
H
Ongoing Battle With Hydraulic Lifters
  • hailer06
  • Jun 8, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
7
Views
614
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 9, 2026
Noobz347
G
Engine Pushrod Length Question
  • germain101
  • Sep 22, 2025
  • Fox 5.0 Mustang Tech
Replies
12
Views
748
Fox 5.0 Mustang Tech Sep 25, 2025
Noobz347
Engine Finishing up 331 build
  • RedFury5.0
  • Mar 21, 2025
  • Fox 5.0 Mustang Tech
Replies
9
Views
767
Fox 5.0 Mustang Tech Apr 20, 2025
RedFury5.0
Engine Looking for suggestions and or ideas
  • PonyGTrider
  • Aug 25, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
715
Fox 5.0 Mustang Tech Sep 7, 2026
PonyGTrider
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?