• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

valvetrain noise/ need help

  • Thread starter Thread starter stevesLX
  • Start date Start date Feb 14, 2007

stevesLX

Member
Nov 12, 2006
373
0
16
cincinnati
Feb 14, 2007
#1
  • Feb 14, 2007
  • #1
I have a 302 w/ a 303F cam stock heads rods and rocker arms. I had the heads milled down. Basically a clean up cut about five thousands taken off and I had the block milled also. A 3 angle valve job and new seals. With that being said I reassembled my heads and got everything back together and I primed the motor before startup and I have valvetarin noise. No knocking just a lot of ticking. You can hear it when it idles but very little. However when you rev it up or when you drive it you can really hear it both inside the car and outside. the rockers are non adjustable pedastal mount. So I tore my valve covers off and did everything all over again. The way I did it was I started at the first cylinder on the drivers side front of the motor. And I turned the crank until I seen the exhaust valve just start to open and then I waited about 1 minute or so for any bleed down and I torqued my intake rocker down to 20 FT LBS. Then I continued to turn the crank until the intake on that same cylinder completely opened and then closed and then I torqed the exhaust rocker down to 20 FT LBS. I did that for every cylinder and each one took about 3/4 of a turn to acheive 20 FT LBS. Started vehicle and still noisy. So I just now tore apart again and checked my preload and I am at about thirty thousands. The tech from Crane Cams tells me they like it to be around 40-45 thousands. So I guess I need longer push rods. I figured they would be to long w/ the hads and the block being cut on. I have been told by some guy to just torque the bolts down to around 22 FT LBS and see what that does. Is it safe to do this w/out damaging anything until I get longer rods or is that a big no no? Will torqueing it down more even help any or am I wasteing my time? Any help would be appreciated.
 
S

superhuaman

New Member
Nov 8, 2004
907
0
0
Harrisburg, PA
Feb 14, 2007
#2
  • Feb 14, 2007
  • #2
switching to 1.7 rockers would make the valves think you had longer pushrods lol. but i dont know if the valves would clear the pistons then.
 
You must log in or register to reply here.

Similar threads

T
Oil burning on my recently buil 302
  • The blk67
  • May 15, 2026
  • Fox 5.0 Mustang Tech
Replies
3
Views
252
Fox 5.0 Mustang Tech May 15, 2026
Noobz347
Engine Looking for suggestions and or ideas
  • PonyGTrider
  • Aug 25, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
748
Fox 5.0 Mustang Tech Sep 7, 2026
PonyGTrider
G
Engine Pushrod Length Question
  • germain101
  • Sep 22, 2025
  • Fox 5.0 Mustang Tech
Replies
12
Views
761
Fox 5.0 Mustang Tech Sep 25, 2025
Noobz347
Resolved Fixing a GT40P Valvetrain nightmare
  • foxbodyclark
  • May 21, 2025
  • Fox 5.0 Mustang Tech
Replies
7
Views
1K
Fox 5.0 Mustang Tech May 24, 2025
limp
S
New misfire after replacing valve seals/springs.
  • SpeedofDarkness
  • Aug 24, 2025
  • SN95 V6 Mustang Tech
Replies
0
Views
321
SN95 V6 Mustang Tech Aug 24, 2025
SpeedofDarkness
S
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?