• Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SN95 4.6L Mustang Tech

VT Blower Cams?

  • Thread starter Thread starter randyp83
  • Start date Start date Jul 13, 2005

randyp83

Member
May 10, 2004
113
0
17
Maysville, NC
Jul 13, 2005
#1
  • Jul 13, 2005
  • #1
Like it says, how much do they cost? how much horse power can i expect. should i get the pi heads for them, because i have a supercharge 98 gt and also where can i buy these things. Thanks for all the info. Randy
 
T

tjm73

Founding Member
Aug 3, 2000
2,418
2
48
Rush, NY
Jul 13, 2005
#2
  • Jul 13, 2005
  • #2
No one talks about it, but you can get a custom made cam set from Ed Curtis at FTI for your specific setup. They don't talk about it on the website (an update is needed for that), but they do make the Mod motor cams too. $750 custom to your car's setup.

to off the shelf cams.

http://www.flowtechinduction.com
 

RedBullitt

New Member
Jul 7, 2004
462
0
0
Morgantown WV
Jul 13, 2005
#3
  • Jul 13, 2005
  • #3
if you are doing a blower, instead of the head swap, just get yours ported, the lower compression will be very blower friendly. just swap the intake tract with some aftermarket parts or port them. cheaper overall
 

96WhiteNight

New Member
May 11, 2004
303
0
0
Carlisle, PA
Jul 13, 2005
#4
  • Jul 13, 2005
  • #4
RedBullitt said:
if you are doing a blower, instead of the head swap, just get yours ported, the lower compression will be very blower friendly. just swap the intake tract with some aftermarket parts or port them. cheaper overall
Click to expand...


Exactly im just gona get mine ported and polished with a 3 angle valve job and cams.
 

DropTopPony

Noob Slayer
Founding Member
Aug 13, 2002
2,570
3
48
south jersey
Jul 13, 2005
#5
  • Jul 13, 2005
  • #5
RedBullitt said:
if you are doing a blower, instead of the head swap, just get yours ported, the lower compression will be very blower friendly. just swap the intake tract with some aftermarket parts or port them. cheaper overall
Click to expand...


this is a good option, if your thinking of porting your npi heads, check these guys out www.steenracing.com you wont have a compression issue if you decide to go this route.
 
You must log in or register to reply here.

Similar threads

M
What cam and heads should I run in my stock 302.
  • MadMatt7
  • Oct 9, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
15
Views
468
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Oct 13, 2026
FastDriver
Electrical problem plug in the drivers kick panel
  • Mindseye007
  • Aug 16, 2026
  • Fox 5.0 Mustang Tech
Replies
3
Views
236
Fox 5.0 Mustang Tech Aug 16, 2026
Mindseye007
Fox Good shop in Washington state or Oregon
  • keel
  • May 14, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
2
Views
180
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- May 20, 2026
keel
A
Blow through intercooled questions
  • AngryH58
  • Aug 31, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
5
Views
286
1996 - 2004 SN95 Mustang -General/Talk- Sep 1, 2026
AngryH58
A
F
Ford 460 swap
  • Ford460
  • Sep 13, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
6
Views
484
1996 - 2004 SN95 Mustang -General/Talk- Sep 14, 2026
Ford460
F
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SN95 4.6L Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?