• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 1994 - 1995 Specific Tech

Water and Oil temp. install Tips?

  • Thread starter Thread starter bqd05
  • Start date Start date Sep 12, 2004
B

bqd05

Founding Member
Dec 7, 2000
121
0
0
Sterling Hts, MI.
Sep 12, 2004
#1
  • Sep 12, 2004
  • #1
I bough Water and Oil temp. gauges and a Clock replacement Pod.
Where should I install the sending units, and also does anybody have any tips on where to go through the firewall?
 

revhead347

Apparently my ex-husband made that mistake.
20+ Year Stangneter
Jun 14, 2004
9,303
1,649
214
Acworth, GA
Sep 12, 2004
#2
  • Sep 12, 2004
  • #2
There is a giant wiring harness with big ass grommet under the driver's side of the dash. You can just poke a hole in the rubber with a screwdriver. It is right above the clutch pedal.

Kurt
 
T

TROJN007

New Member
Apr 15, 2004
72
0
0
Greenwood IN
Sep 12, 2004
#3
  • Sep 12, 2004
  • #3
I used the same gromet for mine. for the sending units, i just went to advanced auto and bought a new thermostat housing that holds a sending unit for the water temperature gauge, and for the oil i just T'd into the stock one with some pipe i bought from home depot.
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Sep 13, 2004
#4
  • Sep 13, 2004
  • #4
yep. for oil, the stock sending unit is 1/4 pipe thread, IIRC. many aftermarket senders are 1/8". might need a small extension to get the senders and tee away from the motor.

is the coolant gauge mechanical? if so, you might need a good sized hole to get the bulbous sender through. you can relocate the stock sender to the rear of the lower intake and put the new sender in the stock location (the rear intake location is not as accurate temp wise).

good luck.
 
You must log in or register to reply here.

Similar threads

Progress Thread Sask84gt's 84 GT - Questions and Progress Thread
  • Sask84gt
  • Oct 13, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
22
Views
1K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 6, 2026
Sask84gt
G
1991 GT 5.0 running hot
  • gvanginkel403
  • Jul 1, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
5
Views
331
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jul 2, 2026
General karthief
M
05 Mustang GT With Annoying P0463 Issue
  • Machbud
  • Oct 17, 2026
  • 2005 - 2009 Specific Tech
Replies
2
Views
196
2005 - 2009 Specific Tech Oct 24, 2026
manicmechanic007
A
A/F ratio gauge install questions.
  • AngryH58
  • Sep 24, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
5
Views
263
1996 - 2004 SN95 Mustang -General/Talk- Oct 22, 2026
Noobz347
D
Paint removal on machined gasket surfaces.
  • Ddyer2868
  • Feb 16, 2026
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
5
Views
398
1965 - 1973 Classic Mustangs -General/Talk- Feb 23, 2026
ctandc
C
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 1994 - 1995 Specific Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?