• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Weird problem after changing heater core...

  • Thread starter Thread starter PeteyAce
  • Start date Start date Feb 11, 2007

PeteyAce

Member
Jul 2, 2004
346
0
17
Feb 11, 2007
#1
  • Feb 11, 2007
  • #1
im not leak everything is fine, heats blowing out nice and hot but weird thing is my temp goes up when i have the heat on (wouldnt it cool the car). goes back down and goes back up but never at a constant temp, but this only when i have the heat on.
 
T

TheUser

Active Member
Jul 25, 2003
1,859
1
36
Springfield, MO
Feb 11, 2007
#2
  • Feb 11, 2007
  • #2
Did you "burp" the system. That is, get all of the air bubbles out.

With a cool engine, jack the front drivers side of the car up to lift the radiator neck above the rest of the cooling system. Next, remove the radiator cap, turn on the heater, and start the car. It's important to turn the heater on to let all of the coolant circulate, not just what's in the block, etc.

You'll notice air bubbles "burping" out. Let it run like that for 15-20 min or so and get all of the bubbles out. Obviously, do not touch the throttle or you'll shoot coolant all over the place. Put your cap back on, lower the car and take it for a drive. If it's not fixed, come back and try again. If that still doesn't fix it, then you may have other issues.
 

TRWXXA

Member
Jan 18, 2003
190
1
19
RIGHT BEHIND YOU!!!... Made you look.
Feb 11, 2007
#3
  • Feb 11, 2007
  • #3
TheUser said:
Next, remove the radiator cap, turn on the heater, and start the car. It's important to turn the heater on to let all of the coolant circulate, not just what's in the block, etc.
Click to expand...
You don't need to turn on the heat. Coolant circulates through the heater core whether the heat is on or not. Turning on the heat just allows air passing through the heater core to enter the cabin. It has nothing to do with coolant flow.
 
D

Daggar

New Member
Jul 19, 2004
3,902
5
0
Feb 11, 2007
#4
  • Feb 11, 2007
  • #4
What you're seeing my very well be air-bubbles in the cooling system showing their presence as the thermostat opens and closes.

Circulating air through the heater core may be changing coolant temp enough to actuate the t-stat.

I'd do what is suggested above and keep burping the system. Come back and hit us up if there's no change after a reasonable amount of time.
 
You must log in or register to reply here.

Similar threads

Engine Bleeding air in the heater core
  • keel
  • Apr 2, 2026
  • Fox 5.0 Mustang Tech
Replies
10
Views
405
Fox 5.0 Mustang Tech Apr 23, 2026
limp
C
Electrical Fuel Gauge...Help! What did I do or Didn't Do?
  • ChickenDeluxe
  • Sep 3, 2026
  • Fox 5.0 Mustang Tech
Replies
2
Views
255
Fox 5.0 Mustang Tech Sep 3, 2026
ChickenDeluxe
C
X
Engine 5.0 Head Gaskets installed wrong block coolant passages???
  • Xam Sirrah
  • Jul 21, 2025
  • Fox 5.0 Mustang Tech
Replies
12
Views
972
Fox 5.0 Mustang Tech Dec 22, 2025
Qtrhrse23
D
Engine Coolant and Radio Issues
  • Don7Up
  • Sep 14, 2025
  • Fox 5.0 Mustang Tech
Replies
17
Views
888
Fox 5.0 Mustang Tech Oct 4, 2025
Don7Up
D
B
A/C Issues
  • Boats90GT
  • Jun 10, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
2
Views
215
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 11, 2026
Mcmahst
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?