• Mustang Forums
  • 1965 - 1973 Classic Mustangs -General/Talk-

What is this 67 Worth ?

  • Thread starter Thread starter 64nahalf
  • Start date Start date Jul 8, 2005

64nahalf

Founding Member
Jul 22, 2002
127
0
0
North Delta , British Columbia , Canada
Jul 8, 2005
#1
  • Jul 8, 2005
  • #1
It runs goods , no leaks that i can find How much is it worth ??
Here is the ad decription and some pics .

1967 Notchback 289-2V 4 speed, Burgandy on Black interior. 126106 miles, I have no idea if that is what is on the engine, but thats what it reads on the odometer. The car is mostly stock, except for 4 things, the color, the wheels, headers and cd player.

* I have just finished doing a bunch of work to it *

Flywheel was turned and balanced, new centerforce dual friction clutch, pressure plate and throw out bearing. New clutch rod, new clutch fork dust boot ( to bellhousing ), new seal in the front of the diff. New thermostat, and thermostat housing gasket, New water pump gaskets, New upper and lower rad hoses, and thermostat hose. New solonoid, and dimmer switch ( high beam foot swtich ). New inline fuel filter, oil changed, tranny oil changed and rear end oil changed. Work that was done to it before it came off the road in 2001 : New rad, new motor mount ( driver's side ), new lower control arms, new ball joints, new leads, plugs, cap and rotor, Sony CD player mounted under the dash with Pioneer 3way 6x9's on the shelf.

Like I said earlier, its pretty much stock, but has headers, the wheels are some American Racing style Centerline knock offs ( not as nice but still look nice ) with 235/60R14 BF Goodrich radial TA's. The cd player I had mounted under the dash, so no dash mods were made, and the stock AM stereo is still in its original spot. Cartunes in port moody did that install. The seats and headliner are near mint, the dash could use a new skin on top. I also have some spare parts for the car : Edelbrock intake manifold for 4 bbl carb, a set of 30 over pistons for a 302, and an extra timing gear set.




 
M

mustangdave

My rearend needs a stud and two nuts.
Founding Member
Feb 26, 2002
2,976
1
56
North Carolina
Jul 8, 2005
#2
  • Jul 8, 2005
  • #2
Couldn't say, but not much with the rust I see, (how much can't you see?). Look at the rust beside the shock tower, that is serious. Rust that bad on the quarters indicates there is probably rusted out cowls, doors, trunk, floorpans,etc... If I'm right, that is about $5,000 in bodywork if you pay someone else. I would pass unless it's free.
 

LMan

Founding Member
Aug 10, 2002
1,246
0
0
Mom's basement
Jul 8, 2005
#3
  • Jul 8, 2005
  • #3
cant tell you about the Canadian market.....but, def rust issues lurking there. You will have to discount heavily for that, if a sensible buyer sees that.

IF your cowl is bad, its $$$$$ and time to repair. I personally would not fool with a standard coupe with serious cowl issues, but thats just me.
 

2nd Mustang

Founding Member
Feb 24, 2002
2,488
0
46
Southern California
Jul 8, 2005
#4
  • Jul 8, 2005
  • #4
I paid $7500 for my 67 coupe, 3 years ago. Many mods already done by the previous owner, so all I had to do was maintain it. No body work required, some was already done, not great, but adequate. I'm sure he spent a lot to get it to that stage. My opinion, would be $3K to $5K. I've seen rust buckets of different makes worst than yours with asking prices of around $5K.
 

Cobain03

Active Member
Aug 27, 2003
996
0
36
Lexington, Ky
Jul 9, 2005
#5
  • Jul 9, 2005
  • #5
i wouldnt say 3-5 personally. i bought mine for 3800 bucks and had no where near that amount of rust. thats a big rust spot on the fender too.
http://i2.photobucket.com/albums/y9/sixt5/mustang_pic3.jpg

thats a pic of mine when i first bought it.
 

65fastback2+2

New Member
Aug 4, 2003
1,229
0
0
Louisville, KY
Jul 9, 2005
#6
  • Jul 9, 2005
  • #6
$3500
 

64nahalf

Founding Member
Jul 22, 2002
127
0
0
North Delta , British Columbia , Canada
Jul 9, 2005
#7
  • Jul 9, 2005
  • #7
Well I found out he is asking 3200usd for it . there is no rust on the frame rails , and the interior is really nice too . just needs a replacement dash pad and some new carpet .the engine bay could really use a detail but thats fine , tires are practically new aswell .
How much does it cost to have a rear quater replaced and painted ??
 
E

electricgreen

Founding Member
Apr 9, 2002
1,140
0
36
Western NY
Jul 9, 2005
#8
  • Jul 9, 2005
  • #8
That really depends on what else they find, and who you have do the work. We just paid someoen we know $3,000 to replace the floor pans, trunk pan, pass torque box
(front), patch both rear torque boxes, the taillight panel, and the pass quarter & wheel housings (inner & outer-came witht he quarter we bought, cut right out of another 73 that had been whacked hard in the front). However, we stripped the interior, trim & windows, and did all the finish work (grind welds, seam seal, paint, filler).

The pics can be hard to tell-but it looks like there's a good bit of rust on the inner fender aprons-at least the tops. Can you look at the car in person? If so, pour water in the cowl (if the owner won't let you-RUN, don't walk!!), and really inspect the under carriage-fresh paint or undercoating can hide some scary things. Check the wheel houses, the front frame rail extensions also-I know these are bad spots on the big bodies, I'd be willing to be it's the same on the earlier bodes as well.
 

64nahalf

Founding Member
Jul 22, 2002
127
0
0
North Delta , British Columbia , Canada
Jul 9, 2005
#9
  • Jul 9, 2005
  • #9
Thanks for the info , The only rust besides that , that I have found it minimal surface rust .
But does any one know about how much it costs to replace OR fix a comparativly damage rear quarter panel ? ?

I have never had body work done before and would like an idea of what to expect so i can plan accordingly'
Thanks
 

65fastback2+2

New Member
Aug 4, 2003
1,229
0
0
Louisville, KY
Jul 9, 2005
#10
  • Jul 9, 2005
  • #10
makes me gr...i cant get 8000usd for my 67 coupe and it has a TON new stuff...needs fender aligning and paint
 

64nahalf

Founding Member
Jul 22, 2002
127
0
0
North Delta , British Columbia , Canada
Jul 10, 2005
#11
  • Jul 10, 2005
  • #11
well if i had 10 grand i would take it . but i don't so i am lookin for some thing just to start with cheap and make it into a 10grand car .
 

2nd Mustang

Founding Member
Feb 24, 2002
2,488
0
46
Southern California
Jul 10, 2005
#12
  • Jul 10, 2005
  • #12
There is always going to be a better deal around the corner, just how willing are you to wait? If this is the first one you've looked at, you may want to keep looking. Body work is the most expensive thing to do on a car, unless you can do it by yourself. I don't know about the quarter panel, but many years ago, someone put a large dent in my passenger side door of my Camaro, it cost $900 dollars at a good body shop to take it out and match the metallic paint, so I imagine it's a whole lot more today.
 

krash kendall

Active Member
Nov 19, 2004
1,258
0
36
Aldergrove, B.C. Canada
Jul 11, 2005
#13
  • Jul 11, 2005
  • #13
Offer him no more than $2200 Canadian. If you get it, I can get you in touch with someone out here in the valley who specializes in restoring mustangs. Ballpark for a quarter panel is $1000 a side if I recall.
 
You must log in or register to reply here.

Similar threads

Thinking of looking at this 67 coupe. Looking for some opinions.
  • billison
  • Aug 11, 2024
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
10
Views
1K
1965 - 1973 Classic Mustangs -General/Talk- Aug 28, 2024
89ripper
6
Hey all,I’m putting together a 302 for my 1968 Mustang and wanted to post the combo + some questions to make sure I’m not missing crucial
  • 68_Disgustang
  • Feb 22, 2026
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
4
Views
902
1965 - 1973 Classic Mustangs -General/Talk- Jun 20, 2026
gray owl
G
A
2001 Mustang GT, scorched metal smell and noise from trans/diff?
  • AndyE2255
  • Dec 1, 2025
  • SN95 4.6L Mustang Tech
Replies
4
Views
465
SN95 4.6L Mustang Tech Dec 28, 2025
gkomo
M
Progress Thread mnky99 2001 V6 evap core, ac compressor, heater core replacement
  • mnky99
  • Sep 5, 2025
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
1
Views
515
1996 - 2004 SN95 Mustang -General/Talk- Sep 5, 2025
mnky99
M
K
TKX Transmission Shifting Problem
  • KWC156
  • Jun 23, 2025
  • Other Auto Tech
  • 2
Replies
21
Views
3K
Other Auto Tech Jun 13, 2026
427nostang
4
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1965 - 1973 Classic Mustangs -General/Talk-
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?