• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

what should i do?

  • Thread starter Thread starter treyh
  • Start date Start date Dec 21, 2007
T

treyh

New Member
Dec 21, 2007
8
0
0
Dec 21, 2007
#1
  • Dec 21, 2007
  • #1
hey im building my first mustang. so far i got a 302 block out if a 93 cobra, stock crank, stock connecting rods, and a f303 cam. planing on puting it in a fox body. so i was thinking about the gt40 heads ported and the street heat intake ported to match. im gonna bore the block over .030. would that be a decent set up and what kind of numbers could i expect. 300??
thanks
 

91 HATCH

Banned
May 17, 2007
262
0
0
illinois
Dec 21, 2007
#2
  • Dec 21, 2007
  • #2
that would be a good setup

280 rwhp or so
 

samickguy15

Member
Sep 1, 2005
404
0
16
Delavan, IL
Dec 21, 2007
#3
  • Dec 21, 2007
  • #3
Go with the GT-40P's. They flow more out of the box. If you add some porting, you're that much ahead. If you're going with a street motor, shoot for high 9's to 10.5:1 compression. A boost in compression will net some good power. if you're planning on a blower later though, leave it around 8.5:1.
 

faststang90

10 Year Member
Nov 5, 2007
522
16
49
baytown texas
Dec 21, 2007
#4
  • Dec 21, 2007
  • #4
heads

i would put the trick flow heads on it. stay with the cam u have put some bigger headers on it. on the intake i would get 1 to go with the heads 24 pound inj, 70mm tb, bigger mass air, with that if u can drive i think low 12 high 11 on motor
 
T

treyh

New Member
Dec 21, 2007
8
0
0
Dec 21, 2007
#5
  • Dec 21, 2007
  • #5
what compresion should i aim for so i can still drive it on the street but spray it when i go to the track?
 

91 HATCH

Banned
May 17, 2007
262
0
0
illinois
Dec 21, 2007
#6
  • Dec 21, 2007
  • #6
9.5 to 10.0 to 1 on 93 octane
 
T

treyh

New Member
Dec 21, 2007
8
0
0
Dec 22, 2007
#7
  • Dec 22, 2007
  • #7
with the f303 cam should i run 1.7 roller rockers? Stock lenth push rods?
 
S

suruat98

New Member
Nov 18, 2006
18
0
1
Dec 22, 2007
#8
  • Dec 22, 2007
  • #8
With the F303 cam you will need to go with 1.6RR and higher lift springs. Stock springs are .500 lift and the cam is above that.
 
You must log in or register to reply here.

Similar threads

C
Electrical Fuel Gauge...Help! What did I do or Didn't Do?
  • ChickenDeluxe
  • Sep 3, 2026
  • Fox 5.0 Mustang Tech
Replies
2
Views
246
Fox 5.0 Mustang Tech Sep 3, 2026
ChickenDeluxe
C
Engine Looking for suggestions and or ideas
  • PonyGTrider
  • Aug 25, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
726
Fox 5.0 Mustang Tech Sep 7, 2026
PonyGTrider
S
Block questions
  • s_vargas54
  • Jan 25, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
21
Views
1K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Feb 8, 2026
Trogdor
A
Discussion on mild budget build/ top end
  • Acesario
  • Feb 21, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
20
Views
1K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Feb 23, 2026
General karthief
First Car, what should I do for power??
  • tunedV6
  • Apr 13, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
7
Views
456
1996 - 2004 SN95 Mustang -General/Talk- May 4, 2026
580HP*428Cj
5
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?