• Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SN95 4.6L Mustang Tech

what's needed w/gears

  • Thread starter Thread starter 97gtconv.
  • Start date Start date Sep 18, 2004

97gtconv.

Member
Jul 31, 2003
244
0
16
Lock Haven, PA
Sep 18, 2004
#1
  • Sep 18, 2004
  • #1
I have a 97 mustang convertible automatic. i have long-tube headers, off-road h-pipe, flowmaster 40 series, steeda underdrive pulleys, bbk cold-air intake and eibach sports springs 1 1/2" drop. The rearend of the car is still the factory 7.5" with i think 2:73 gears.

My question is that I want to get 3:73 or 4:10. i really want 4:10's but i need to know what else i need besides the ring and pinion. do need oil? something to adjust the speedometer. i need some help cause i don't want to screw this up. any bodies help would be greatly appreciated.

thanks
 

TweekedGT

New Member
Jul 22, 2004
1,274
0
0
Alberta
Sep 18, 2004
#2
  • Sep 18, 2004
  • #2
If you purchase the kit from Ford it will come with a crush collar and some shims, a ring and a pinion. I bought FRPP 3.73's and they work awesome. Over and above what comes in the kit you will need two bearings and two races, some grease for the bearings, 2 litres of 80/90 gear oil for your differential once you are completed the install. I just switched my gear oil out and am using Amsoil synthetic gear oil now, i believe it is 75/140, can't remember. You will also need some silicone as gasket maker for your dif housing or an actual dif cover gasket, your choice. If you are planning on doing this yourself you will also need a dial gauge to measure the backlash of your gears to make sure there is not to little or too much resistance. I hope i didn't forget anything. Have fun, you will love the gears!
 

GTMomma02

New Member
Jul 15, 2003
350
0
0
moving to CA...
Sep 18, 2004
#3
  • Sep 18, 2004
  • #3
97gtconv. said:
My question is that I want to get 3:73 or 4:10. i really want 4:10's but i need to know what else i need besides the ring and pinion. do need oil? something to adjust the speedometer. i need some help cause i don't want to screw this up. any bodies help would be greatly appreciated.

thanks
Click to expand...

I think it depends on where your gears are installed. The shop that did mine told me to just bring the gears and they had everything else. I don't think you can use a speedcal on an automatic so you need to have your computer reflashed or buy a chip. I decided to have my computer flash-tuned because it was almost the same price, and they adjusted a/f ratio, shift points and bumped the timing. Good luck!
 

TweekedGT

New Member
Jul 22, 2004
1,274
0
0
Alberta
Sep 18, 2004
#4
  • Sep 18, 2004
  • #4
Oh ya! You will need a new speedo gear to adjust the speedometer. I know the 99+ GT's can get there's calibrated through the computer but I don't think we can. I had to by a new speedo gear. It goes right by the drive shaft u-joint right in the tranny. You have to unbolt the cable, pull the old gear out, and put the new one on and bolt it up again. Once you find where the speedo cable is it is a 2 minute job.
 

GTMomma02

New Member
Jul 15, 2003
350
0
0
moving to CA...
Sep 18, 2004
#5
  • Sep 18, 2004
  • #5
TweekedGT said:
Oh ya! You will need a new speedo gear to adjust the speedometer. I know the 99+ GT's can get there's calibrated through the computer but I don't think we can.
Click to expand...

Whoops! Sorry, I'm not up on 96-98 GTs.
 

97gtconv.

Member
Jul 31, 2003
244
0
16
Lock Haven, PA
Sep 18, 2004
#6
  • Sep 18, 2004
  • #6
I just want to clarify that my car 1997 Mustang Gt conv. comes with the 7.5" rearend w/ 10 bolt differential cover. is that what i have?
 

madmatt

Ellis Juan sympathizer
Founding Member
Dec 28, 2002
465
0
16
Lexington, SC
Sep 18, 2004
#7
  • Sep 18, 2004
  • #7
Should be an 8.8 I believe. The 7.5 is in the V6 only I think. Not 100% sure though.
 
You must log in or register to reply here.

Similar threads

C
Need 1973 Mustang schematic
  • Cudajim
  • Sep 28, 2025
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
18
Views
872
1965 - 1973 Classic Mustangs -General/Talk- Oct 10, 2025
manicmechanic007
J
2004 Mustang 3.8L V6 vibrations above 65 MPH and differential leaks
  • joeybuddy96
  • Mar 16, 2026
  • SN95 V6 Mustang Tech
Replies
17
Views
1K
SN95 V6 Mustang Tech Aug 29, 2026
joeybuddy96
J
F
Ford 460 swap
  • Ford460
  • Sep 13, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
6
Views
472
1996 - 2004 SN95 Mustang -General/Talk- Sep 14, 2026
Ford460
F
5
Hello Everyone !
  • 5150K
  • Jul 3, 2026
  • The Welcome Wagon
Replies
0
Views
184
The Welcome Wagon Jul 3, 2026
5150K
5
What's your tow rig?
  • LILCBRA
  • May 31, 2026
  • Other Auto Tech
Replies
9
Views
477
Other Auto Tech Oct 23, 2026
JH96GT
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SN95 4.6L Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?