What's the best way to remove pilot bearing?

Justin81

New Member

Jan 9, 2012

22

0

1

Pittsburgh

Feb 2, 2012

#1

• Feb 2, 2012

• #1

Is there an easy way to remove the pilot bearing. I tried packing the area behind the bearing with grease and used a socket extension and hammer to try and compress it out. Didn't work. Do you have to beat the grap out of the socket extension? I didn't want to damage the crankshaft. The bearing didn't even seem like it move at all while trying this. Is there a better way? I'm swapping out the clutch and knew I was going to hit a road block because everything was going way too easy.

 

jrichker

StangNet's favorite TOOL

In Remembrance. Thank you for your contributions

Mar 10, 2000

27,512

2,813

234

Dublin GA

Feb 2, 2012

#2

• Feb 2, 2012

• #2

Check with the AutoZone or Advanced Auto Parts or other major auto parts chain store in your area for a loaner pilot bearing tool. The bearing will probably come out in two pieces, but using the puller, it will come out. I have done it two or three times and it worked for me.

 

R

rockyracoon

10 Year Member

Nov 23, 2005

874

27

49

margate NJ

Feb 2, 2012

#3

• Feb 2, 2012

• #3

They have the pilot removal tools at harborfreight at least they used to have em. I used ( believe it or not) plumbers putty and a piece of dowel, worked like a charm. in the past when I had a really stubborn one I used a dremel with a little cutting wheel to create a crack in the race (that was after I ripped all of the guts out with my puller) I was ultra careful not to go too deep. Then I did the compression thing with the putty.

 

boostfrk

10 Year Member

Aug 30, 2011

712

69

59

Colorado

Feb 2, 2012

#4

• Feb 2, 2012

• #4

I rented the tool from Advanced Auto. Came out on the first try.

 

TwoToneHatch

Active Member

Mar 22, 2007

170

2

28

New Jersey

Feb 2, 2012

#5

• Feb 2, 2012

• #5

Definitely get the pilot bearing removal tool . I got mine with a slide hammer from Autozone and I've done 5 pilot bearings and the tool made it simple .

 

need4spd90

Member

Jun 3, 2008

106

6

19

Mountain Top, PA

Feb 3, 2012

#6

• Feb 3, 2012

• #6

i use modeling clay or grease

 

ID89GT

10 Year Member

May 26, 2008

1,659

18

49

Spokane Valley, WA

Feb 3, 2012

#7

• Feb 3, 2012

• #7

Yep the tool is the only way ive been able to do it.

 

1990Coupe

Founding Member

Mar 11, 2002

1,462

132

114

Toms River NJ

Feb 3, 2012

#8

• Feb 3, 2012

• #8

I used grease and a wooden dowel. I've taken 4 out this way, no issues ever with any of them.

 

gearheadboy

15 Year Member

Jan 15, 2003

1,425

177

84

Greencastle Pa

Feb 3, 2012

#9

• Feb 3, 2012

• #9

Just did mine a few months back. Used the torn up wet wadded paper and a nut driver. Make sure the paper is WET and yes ya gotta beat it, but it comes out nice and clean. NO DAMAGE

 

Justin81

New Member

Jan 9, 2012

22

0

1

Pittsburgh

Feb 4, 2012

#10

• Feb 4, 2012

• #10

I rented the pilot bearing removal tool from autozone and was only able to remove the bearing from the bushing. I ended up breaking one of the claws on the tool trying to remove the bushing. Returned it to autozone and rented there blind hole puller tool and had the bushing out within a minute. If it wasn't so pricey I would of just bought it. It saved me from chiseling away at the bushing.

 

BlackGT89

Member

Dec 16, 2002

774

8

18

Huntsville, AL

Feb 4, 2012

#11

• Feb 4, 2012

• #11

I tried the grease method, it was way too messy for me, made all of the tools too slippery to work with. Someone suggested bar soap cut into bits and crammed in the hole, and it actually worked for me. Looking back on it, I think it best to just rent/borrow the tool...

 

NIKwoaC

中國製造

15 Year Member

Oct 31, 2006

5,525

943

214

Chengdu Province

Feb 4, 2012

#12

• Feb 4, 2012

• #12

The grease/wet paper/clay/soap/jizz method is a joke, it seems to work every time for some people, but never for others. Whether it works or not, it always makes a mess. The tool is the way to go, it's actually designed for the job and it won't leave you wiping bearing grease off of every contactable surface in a 3 foot radius, haha.

 

gearheadboy

15 Year Member

Jan 15, 2003

1,425

177

84

Greencastle Pa

Feb 5, 2012

#13

• Feb 5, 2012

• #13

Thats why I used wet paper. No mess. And no marks in the crank. The key is to have the thing full before ya start hammering and make the socket fit the hole as tight as possible without getting stuck. Works slick every time.