Whats the biggest cam a stock 5.0 can hold help

BarefootPainter · Jan 17, 2013

As it says I need to ow the biggest cam I can put in a stock 5.0 bottom end and stock heads without doing
Major valve work.granted I know springs lifters and poss pushrods halfta be changed accordingly.but I love the sound of the z cam so what's ur guys suggestions any and all appreciated.cars a 5 speed with. 1.95 gear set 373's msd hvc ignition box and coil same setup NASCAR uses aluminum intake and Holley carb.havent got the intake yet wanted to get the cam first and go from there.thanks guys and all input is appreciated!

gearheadboy · Jan 17, 2013

Son, son, son... The biggest cam you can ram in your block with stock heads and pistons is gonna run like poo, not to mention there are about a hundred definitions of big cam. You are gonna end up with a top end cam and intake with a bottom end bottle neck head. Think about what you are looking to achieve and come back for answers.

BarefootPainter · Jan 17, 2013

Ok ha halfway expected that answer after I read what I posted.car will be a daily driver but I halfta say my commute mileage wise is not far.im leaning towards one of the frpp cams either the e cam or f cam because I've heard great things about their power gains and drive ability.i want sumthin that will hit and sound rather nice and go along with what I've got as listed above.so which one of the frpp cams would u recommend that'll still give me the sound I want.

Noobz347 · Jan 17, 2013

You will not see a significant performance improvement with a non OEM cam and an otherwise, stock engine.

jka · Jan 17, 2013

If you are just looking for sound plus a few hp go with a trick flow stage 1 or a n-41 cam ...both are good cams and will work. Also if you install heads later these cams will work good with GT40 heads and trick flow heads without problems.

BarefootPainter · Jan 17, 2013

What's the specs on those two cams and will I halfta worry about piston to valve clearance

jka · Jan 17, 2013

The stage 1 cam specs are 221/225 duration 499/510 lift and will work with stock heads aftermarket trick flow heads and GT40 heads without problems. Also you will not have any problems with piston to valve clearance..and i think the n-41 cam has a lift of 512 and that will work with stock pistons. You need to use better than stock valve springs and you may want use harden pushrods.

mikestang63 · Jan 17, 2013

Why are you looking to change cams? I've made 11's with the stock cam. What is the rest of your setup. Heads, induction, compression, etc. Throwing a big lift or duration cam at an otherwise stock setup is not only foolish, but will result in poor drivabillity and performance.

stykthyn · Jan 17, 2013

a buddy of mine has a stock head/intake car with an f cam. sounds like a stock car and makes a whopping 150 to the wheels. My ram truck would outrun it on a regular basis.
Keep the stocker unless you are upgrading the top end as well.

ratio411 · Jan 17, 2013

What tranny do you have?
If you have an auto trans, you have driveability issues to worry about with most aftermarket cams unless you get a stall converter.

David Pepiton · Jan 17, 2013

he said it was a 5 speed.

in all honesty unless your doing heads keep the stock cam and work on other bolt-ons. cold air intake, larger TB, Intake manifold, full exhaust should be your first steps if you dont have the basics your already wasting your time.

also where is this nascar crap coming from? are you driving a race car?

stangman11 · Jan 18, 2013

You might as well wait and do a whole top end kit if you really wanna stick with the stock bottom end. If you just throw a big cam in it you wont get the performance you want plus the valves will just end up floating.

BarefootPainter · Jan 18, 2013

Running a t5 wit a stage 2 clutch and 195 gear set.been looking into heads now and I'm looking at a set of either Doug Herbert heads or performer rpm's bc I can pick em fairly cheap brand new through a friend of mine.hut yes for now the bottom end will stay stock until I build a 347.

billison · Jan 18, 2013

If you are gonna tear it down to install a cam at least toss a set of gt40's on that bad boy..

Go get a McDonald's straw and suck as hard as you can... That's what you'll be doing to your car.

David Pepiton · Jan 18, 2013

im going to suggest you do a lot of reading and research. before you spend thousands of dollars to have a 300 hp car you need to do your research and read around and not buy anything untill youve come up with a end goal/ hp and build accordingly.

ReefBlueHatch · Jan 18, 2013

1.95 gear set in a 8.8 - never heard of that ratio. Even if you did put a cam in a stock motor (bad idea) you'll need 3.55 gears or lower.

The FRPP "letter" cams are the most outdated hydraulic roller cams available for the 5.0 - there's a lot better options available with split durations.

srtthis · Jan 18, 2013

1.95 gear set??? wtf???
who makes a 1.95 gear set for a T5?
this is the point where im going to come off like an ******* and im ok with that. do you have ANY idea what the hell your doing?

f8tlfiveo · Jan 18, 2013

Maybe he is talking about 2nd gear.. I think that's around 1.95..

David Pepiton · Jan 18, 2013

srtthis said:
1.95 gear set??? wtf???
who makes a 1.95 gear set for a T5?
this is the point where im going to come off like an ******* and im ok with that. do you have ANY idea what the hell your doing?

i dont think he does.

srtthis · Jan 18, 2013

f8tlfiveo said:
Maybe he is talking about 2nd gear.. I think that's around 1.95..

IIRC all of them are around 1.93-1.94 first gear is the one thats different with a 3.35 and a 2.95....

Whats the biggest cam a stock 5.0 can hold help

BarefootPainter

New Member

gearheadboy

BarefootPainter

New Member

Noobz347

Stangnet Facilities Maint Tech... Er... Janitor

jka

BarefootPainter

New Member

jka

mikestang63

stykthyn

I want to measure mine. It doesn't look that tall.

ratio411

David Pepiton

Active Member

stangman11

Member

BarefootPainter

New Member

billison

I like tinted tail

David Pepiton

Active Member

ReefBlueHatch

Active Member

srtthis

the guy doing it does every local racers rear end

f8tlfiveo

My wife likes my spool and blow-off valve.

David Pepiton

Active Member

srtthis

the guy doing it does every local racers rear end

Similar threads

Whats the biggest cam a stock 5.0 can hold help

New Member

New Member

Stangnet Facilities Maint Tech... Er... Janitor

New Member

I want to measure mine. It doesn't look that tall.

Active Member

Member

New Member

I like tinted tail

Active Member

Active Member

the guy doing it does every local racers rear end

My wife likes my spool and blow-off valve.

Active Member

the guy doing it does every local racers rear end

Similar threads

Privacy & Transparency

Privacy & Transparency