• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

wheel hop!! suggestions

  • Thread starter Thread starter green9150
  • Start date Start date Apr 29, 2004
G

green9150

New Member
Nov 16, 2003
13
0
0
Apr 29, 2004
#1
  • Apr 29, 2004
  • #1
i need help. i just installed a set of x2c upper and lower control arms a set of comp eng 3way ajustable shocks set at 50/50. Also i have g-force drag springs with the air bag in one. i installed it at work and used my 1/2 air gun on the upper and lowers i took it out on a test run i had alot of wheel hop just punching it out of idle. I thought i over tighten them and i lossen and tighten them to spec 100 lbs. took it out a little better but close to the same. the least amount of hop i get with 9 psi in the air bag and 28 psi in the tires. do you gus think i need upper axle bushings.i get hop when i rev to 1600 rpms and above and drop clutch. and also when i slam 2nd. also in addition i have 225 70 15 out back and no quad shocks i was going to buy a pair because i thought it would improve the hop. I am going to drop a new engine in it in a couple of months and i just see it getting worse. any suggestions? thanks guys
 

cjman15

Banned
Apr 15, 2004
1,009
0
0
Fairfield, PA
Apr 29, 2004
#2
  • Apr 29, 2004
  • #2
def get the quad shocks, i have them on my '89 LX and i never have any wheelhop problems... burnouts are nice and clean, even with sticky tires...haha
 
8

85GTlover

New Member
Mar 20, 2004
704
0
0
Apr 29, 2004
#3
  • Apr 29, 2004
  • #3
Yes for sure quad shocks, that is what they are for although sometimes they do not do a great job.
 

ECU5.0

Banned
Jan 10, 2004
1,803
1
0
raleigh, nc
Apr 29, 2004
#4
  • Apr 29, 2004
  • #4
yeah, run quad shocks until your tires get too big for them. my buddy had to take his off, he runs a 265 tire. it wheel hops a little bit every once in a while...but when it hooks, it hooks hard
 
M

Matts89LX5.0

Founding Member
Nov 1, 2002
1,314
0
36
Long Island, NY
Apr 29, 2004
#5
  • Apr 29, 2004
  • #5
never heard of wheel hop with after market control arms.

Matt
 

bgjohnson

Founding Member
Sep 1, 2002
963
0
16
johnston,iowa
Apr 29, 2004
#6
  • Apr 29, 2004
  • #6
when you got new control arms, did you get new bushings too?
 
You must log in or register to reply here.

Similar threads

D
For Sale 1993 Mustang LX for parts or restore
  • diesel farmer
  • Oct 6, 2026
  • Fox Body Mustangs For Sale (1979-93)
Replies
0
Views
414
Fox Body Mustangs For Sale (1979-93) Oct 6, 2026
diesel farmer
D
Resolved 93 Mustang 5.0 - Cranks but does not start
  • dan50
  • Jul 18, 2026
  • Fox 5.0 Mustang Tech
Replies
6
Views
485
Fox 5.0 Mustang Tech Jul 18, 2026
dan50
Most ridiculous / dishonest work you have heard a shop recommend?
  • SchwarzStock
  • Jul 19, 2026
  • Off-Topic Hangout
Replies
4
Views
146
Off-Topic Hangout Jul 20, 2026
SchwarzStock
Resolved Got Too Hot!!!
  • PonyGTrider
  • Apr 27, 2025
  • Fox 5.0 Mustang Tech
Replies
7
Views
762
Fox 5.0 Mustang Tech May 6, 2025
PonyGTrider
Drivetrain Rear end clunk
  • seanmahoney
  • Oct 13, 2025
  • SN95 4.6L Mustang Tech
Replies
3
Views
525
SN95 4.6L Mustang Tech Oct 13, 2025
nickyb
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?