• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Which head gaskets are you using with stock 302 block?

  • Thread starter Thread starter VibrantRedGT
  • Start date Start date Jun 15, 2011

VibrantRedGT

"STANGNET'S PENGUIN SMACKER"
15 Year Member
Nov 29, 1999
14,679
424
154
Boca Raton, Florida
Jun 15, 2011
#1
  • Jun 15, 2011
  • #1
Man, just did a search and the answer is all over the place. Seems FelPro 9331's are common. However now they're are so many out there.

What are using?
 

Rick 91GT

Mustang Master
Nov 29, 1999
9,692
95
99
PA
Jun 15, 2011
#2
  • Jun 15, 2011
  • #2
Either 8548pt2, 9333 or 1011-2 in the Fel-Pro brand
 

VibrantRedGT

"STANGNET'S PENGUIN SMACKER"
15 Year Member
Nov 29, 1999
14,679
424
154
Boca Raton, Florida
Jun 15, 2011
#3
  • Jun 15, 2011
  • #3
We are using the 8548pt2. What's the difference between this and the others? This will be a N/A car for awhile and later possible 125HP shot. The mods in sig. below.
 
8

89llx

5 Year Member
Aug 31, 2009
302
5
29
Jun 15, 2011
#4
  • Jun 15, 2011
  • #4
I use the wire lock, and yes you can blow them, but at that point its better the headgasket blow than something else
 

RangerJoe

I leave the horn on while driving
15 Year Member
Apr 26, 2010
2,560
1,146
184
Georgia
Jun 15, 2011
#5
  • Jun 15, 2011
  • #5
I used the 1011-2's the last go around. For a mild build I think they work very well. My father-n-law has used them on a 400hp,11.5:1 compression strip motor for several years and never had a problem with them. If you decide to go with these, they can be bought cheaper as Ford Racing Gaskets. I don't have the part# on hand, but I bought them from Late Model Restoration under the FRPP name and they are the same thing as Fel-Pro 1011-2...they have it stamped right on the edge. They were significantly cheaper this way.
 

Chrome_Rust

Member
Dec 5, 2008
530
1
17
Findlay, Ohio
Jun 15, 2011
#6
  • Jun 15, 2011
  • #6
RangerJoe said:
I used the 1011-2's the last go around. For a mild build I think they work very well. My father-n-law has used them on a 400hp,11.5:1 compression strip motor for several years and never had a problem with them. If you decide to go with these, they can be bought cheaper as Ford Racing Gaskets. I don't have the part# on hand, but I bought them from Late Model Restoration under the FRPP name and they are the same thing as Fel-Pro 1011-2...they have it stamped right on the edge. They were significantly cheaper this way.
Click to expand...

Same thing I have.
 

Rick 91GT

Mustang Master
Nov 29, 1999
9,692
95
99
PA
Jun 15, 2011
#7
  • Jun 15, 2011
  • #7
I listed the gaskets in the order stock replacement, better, best (when using a stock head)
 

VibrantRedGT

"STANGNET'S PENGUIN SMACKER"
15 Year Member
Nov 29, 1999
14,679
424
154
Boca Raton, Florida
Jun 15, 2011
#8
  • Jun 15, 2011
  • #8
I hope these hold up. I wanted to do 1011's.

Rick what are you torquing ARP head bolts down on aluminum heads with 8548's? I think we are at 65 or 68 right now. We did 3 part torque number in specific sequence as recommended.

Little worried about the timing cover install. The bottom cork oil pan gaskets moved during the install. The driver side oil pan bolt to the timing cover seems like its just spinning (just one out of the two). I would die if we had to do it all over again. The heat index has been over 100 for 8 straight days with 100% humidity and getting hotter.

We are down to installing front accessories and upper intake. Oh and we have to remove the stock fuel pump for a 255.
 

2000xp8

SN Certified Technician
Aug 8, 2003
8,077
1,659
194
NJ
Jun 15, 2011
#9
  • Jun 15, 2011
  • #9
It's pretty rare that a head gasket blows and that it's the head gasket itself that's at fault.
Detonation, improper install, acidic coolant, overheating are usually what kills a head gasket.
My buddy uses 9333pt1's on almost everything, if it detonates, you would rather replace a head gasket than a piston or crank.
 

Rick 91GT

Mustang Master
Nov 29, 1999
9,692
95
99
PA
Jun 15, 2011
#10
  • Jun 15, 2011
  • #10
I torque them to the ARP spec, I use black Permatex on the lower bolts per the advice of a ARP tech after I had a string of bad luck with the ARP liquid teflon.

We run the 8548 on a Renegade car at 24+ lbs of boost when it was all we could get our hand on.

Hey XP, my motorplates will be here monday. Project 32v will be in full effect.
 
You must log in or register to reply here.

Similar threads

speedmaster new 302 block?
  • rednotch
  • Aug 9, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
29
Views
896
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 16, 2026
rednotch
J
can you use the heads off a H O 302 to put on a regular 302 engine
  • Jan H
  • Feb 25, 2026
  • Other Auto Tech
Replies
6
Views
608
Other Auto Tech May 17, 2026
nickyb
Engine Head gasket port matching plus head/intake port alignment
  • PonyGTrider
  • Dec 10, 2024
  • Fox 5.0 Mustang Tech
Replies
6
Views
661
Fox 5.0 Mustang Tech Dec 12, 2024
PonyGTrider
A
Resolved 302 oil leak when running
  • AlexM556
  • Sep 8, 2026
  • Classic Mustang Specific Tech
  • 2
Replies
36
Views
1K
Classic Mustang Specific Tech Nov 1, 2026
manicmechanic007
S
Block questions
  • s_vargas54
  • Jan 25, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
21
Views
1K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Feb 8, 2026
Trogdor
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?