Will a 95 crown vic 4.6 work in a 96 gt?

Jacob_Royer · May 30, 2010

A friend is selling a running 95 crowm vic 4.6 for $50 im wanting to buy it and build it to swap into the mustang. Will this 4.6 work? is there any diffrences i should know about? The plan is eaither a PI head FI build or a NA Trickflow head build.

KBExperience · May 30, 2010

There are little odds and ends that are Gonna be different like a few sensors.: and the intake, but the intake shouldn't be an issue If you're building it. 50 bucks is a good
deal!

Jacob_Royer · May 31, 2010

This car is a daily driver with over 200k and gets 700+ miles a week on it. I would like to keep mileage and reliabilty somwhere in the realm of reasonable. I get 25/27mpg as it is. I would like to get up around 300hp i drove a mach1 the other day and would be very happy with that kind of performance. Can 300hp be achieved with PI heads NA? or Is trick flow the way to go? Or what about these 5.0 stroker kits? single turbo?

ninjastang125 · May 31, 2010

Yes 300hp na is acheivable with p.i. heads. With the added compression from the head swap, bigger cams, longtubes and bolt ons you should be very close to 300hp. Do ported heads or trickflows and 300 will be surpassed easily. This combo will make good power and will run 11s with a driveer and 5 speed in the 1320.

wmburns · Jun 1, 2010

The 95 block is not as good as the 96+ casting. So if you want a DD, the 95 is fine.

On the other hand if more HP is on your mind, IMO a 96+ block is a better choice.

nickmckinney · Jun 1, 2010

The pre 96 blocks don't have cross bolts on the rear main, and the heads are total craptastic junk.

98COBRA281 · Jun 1, 2010

nickmckinney said:
and the heads are total craptastic junk.

i read somthing that they dont even consider the pre '96 heads to be NPI's?

Jacob_Royer · Jun 2, 2010

Well i dont plan on keeping the heads... but what about this block strength isue? is it going to be a problem with an NA build? should i just forget about this engine and find somthing else? seems like a steal to me.

nickmckinney · Jun 2, 2010

98COBRA281 said:
i read somthing that they dont even consider the pre '96 heads to be NPI's?

The gaskets are all the same but the pre beehive springs they have can't do over 500 lift. Plus the intake port just plain sucks on them.

nickmckinney · Jun 2, 2010

Jacob_Royer said:
Well i dont plan on keeping the heads... but what about this block strength isue? is it going to be a problem with an NA build? should i just forget about this engine and find somthing else? seems like a steal to me.

Mild NA it would be fine IMHO.

Jacob_Royer · Jun 4, 2010

So freshened up npi short block with PI heads Intake and aftermarket cams + Longtube headers would get me close mach1 performance and keep the mpg's reasonable?

I have:

PI intake
JLT CAI
Mac U/D pullies
Motorsport Shorty Headers
Magnaflow OR X-pipe
Flowmaster American Thunder Catback
3.27's
King Cobra Clutch
Steeda Quadrant/cable/firewall adjuster
American Muscle Short Throw Shifter

I wouldnt mind ditching the shorty headers while the motor is out! i keep blowing the collector gaset! (about once a year) royal pita to replace! plus my xpipe has a pinhole in it. (i can weld it and few months later it leaks again) so the headers and X pipe need replaced anyway. I will need PI heads though and ?? cams? whats a good grind with my setup? and with running pi heads on a NPI motor? also would a tune be a good idea at this point?

fast97gt · Jun 5, 2010

You would need a tune just doing a PI swap regardless of cams, but to answer would definitly get a dyno tune from a reputible shop. You should see more then 300hp n/a with all the LTs H/C/I tune etc. Good luck to ya

Jacob_Royer · Jun 5, 2010

Will that be enough to get my 9.4xx 1/8th mile times down to low 8's?

fast97gt · Jun 6, 2010

mid 8s if you can drive and a descent suspension and tires, i run a full PI engine and have an alrite suspension and 285/18 nittos and ran a 8.93 last weekend and no tune or cams

Will a 95 crown vic 4.6 work in a 96 gt?

Jacob_Royer

Member

KBExperience

Active Member

Jacob_Royer

Member

ninjastang125

New Member

wmburns

nickmckinney

Member

98COBRA281

Jacob_Royer

Member

nickmckinney

Member

nickmckinney

Member

Jacob_Royer

Member

fast97gt

Active Member

Jacob_Royer

Member

fast97gt

Active Member

Similar threads

Will a 95 crown vic 4.6 work in a 96 gt?

Member

Active Member

Member

New Member

Member

Member

Member

Member

Member

Active Member

Member

Active Member

Similar threads

Privacy & Transparency

Privacy & Transparency