• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

wiper switch connections

  • Thread starter Thread starter stang0f87
  • Start date Start date Oct 17, 2007
S

stang0f87

Member
Aug 16, 2004
102
0
16
Fort Smith, AR
Oct 17, 2007
#1
  • Oct 17, 2007
  • #1
ok the turn signals went out on my 87 gt. my old wiper/turn signal switch looks pretty bad anyways, so i figured what the hay. even if that doesn't fix it, i wanna change it out anyways. so after disconnecting the plugs in the back of the switch, some of the wires come out of the plugs and i don't know where they go. does anyone got a schematic or pictures that could help me out?
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Oct 17, 2007
#2
  • Oct 17, 2007
  • #2
I have a wiring diagram set from an 89 Mustang. The turn signal should be the same.



If you need more, PM me your email address and I will send you a zip file with the whole wiring diagram set. It is too big to pass through Stangnet's email gateway.
 
S

stang0f87

Member
Aug 16, 2004
102
0
16
Fort Smith, AR
Feb 3, 2008
#3
  • Feb 3, 2008
  • #3
thanx jrichker. i was able to verify all my wires were plugged in right. turn signals still don't work. i was lookin at my hazard switch and i'm wondering bout two things. 1st, there are two plugs that go into the hazard switch. hazards will still work when i unplug the smaller one. what is the function of that smaller plug with just 3 wires. 2ndly, when i pulled the smaller plug and looked inside the switch, i can't see any copper thingies sticking up where it plugs in. just 4 empty little holes where it looks like they oughta be. wonder if this has anything to do with my turn signal problem?
 

Saleen0679

10 Year Member
Apr 14, 2005
876
24
49
Yakima, WA
Feb 3, 2008
#4
  • Feb 3, 2008
  • #4
The Hazard switch only uses the top connector. The bottom connector is used by either an active Rear Window Defrost switch or Convertible top switch. It sounds like you just have the dummy switch for the bottom section.
 
S

stang0f87

Member
Aug 16, 2004
102
0
16
Fort Smith, AR
Feb 3, 2008
#5
  • Feb 3, 2008
  • #5
bump
 
S

stang0f87

Member
Aug 16, 2004
102
0
16
Fort Smith, AR
Feb 3, 2008
#6
  • Feb 3, 2008
  • #6
bump
 
S

stang0f87

Member
Aug 16, 2004
102
0
16
Fort Smith, AR
Feb 3, 2008
#7
  • Feb 3, 2008
  • #7
ok i've got the classic hazards work but turn signals don't work problem. i went ahead and replaced both flashers. new wiper switch. new ignition switch. bulbs work fine when i hit the hazard switch so they're fine. runnin out of ideas. i should mention the turn signals went out slowly. they would actually quit for a while and then come back. now nothing
 

Saleen0679

10 Year Member
Apr 14, 2005
876
24
49
Yakima, WA
Feb 4, 2008
#8
  • Feb 4, 2008
  • #8
The turn signals use a separate set of contacts inside the Hazard switch. With the hazards off you should have power on the LB wire from the flasher into the switch and coming out on the O/Y wire at the back of the Hazard switch. If not, the switch is bad.
 
S

stang0f87

Member
Aug 16, 2004
102
0
16
Fort Smith, AR
Feb 4, 2008
#9
  • Feb 4, 2008
  • #9
ok i've got power coming out of the switch on the orange/yellow wire. i checked the orange/yellow wire at the turn signal switch. its hot. is there a way to test the turn signal switch or should i be chasin wires?
 
S

stang0f87

Member
Aug 16, 2004
102
0
16
Fort Smith, AR
Feb 4, 2008
#10
  • Feb 4, 2008
  • #10
bump
 
S

stang0f87

Member
Aug 16, 2004
102
0
16
Fort Smith, AR
Feb 4, 2008
#11
  • Feb 4, 2008
  • #11
ok just tried something different. i pulled the plug from the back of the wiper switch. ran a jumper from the orange wire to the other wires on the plug. turn signals worked that way. does that mean the wiper switch is bad? its brand new?
 
S

stang0f87

Member
Aug 16, 2004
102
0
16
Fort Smith, AR
Feb 4, 2008
#12
  • Feb 4, 2008
  • #12
bump
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Feb 4, 2008
#13
  • Feb 4, 2008
  • #13
Are you sure the new switch is for 87-89 model Mustangs?

A word of caution about multifunction switches is in order here. The multifunction switch (high/low beam, wiper, turn signals) are different for different years. 87-98 will work in any 87-89 car. The 90-93 switches only work in 90-93 cars. You can't put an early model switch in a late model car, nor can you put a late model switch in an early car.

Supposedly you can move the pins around to make the switches work in model years that are different from the car the switch came out of. I cannot verify that and haven’t tried it .
 
You must log in or register to reply here.

Similar threads

Electrical 1986 Mustang GT Multifunction Switch Question
  • Willybill32
  • Oct 26, 2025
  • Fox 5.0 Mustang Tech
Replies
11
Views
740
Fox 5.0 Mustang Tech Nov 22, 2025
Willybill32
D
Electrical Weird door wiring issues
  • Dakar09
  • Oct 20, 2026
  • Fox 5.0 Mustang Tech
Replies
4
Views
207
Fox 5.0 Mustang Tech Oct 21, 2026
Dakar09
D
J
Electrical Cluster bulb LED swap gauges bounce
  • jpfox
  • Jun 29, 2025
  • Fox 5.0 Mustang Tech
Replies
1
Views
267
Fox 5.0 Mustang Tech Jun 29, 2025
gkomo
Electrical Parasitic Draw, Fuse 8
  • N8827N
  • Sep 15, 2026
  • Fox 5.0 Mustang Tech
Replies
6
Views
288
Fox 5.0 Mustang Tech Sep 18, 2026
AeroCoupe
A
Electrical electric mirror switch issue...
  • alchemist1
  • Apr 18, 2026
  • Fox 5.0 Mustang Tech
Replies
1
Views
189
Fox 5.0 Mustang Tech Apr 19, 2026
2000xp8
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?