yoke/universial pics....is this right?

streetgrande69 · Nov 4, 2004

this is a continuation of this thread......
http://forums.stangnet.com/showthread.php?p=4721004&posted=1#post4721004
with pics
you can see how its off center.....it isn't wide enough for the yoke. this is the same ujoint for my car and the car the yoke is for so i'm kinda confused.anyway regardless, i'm gonna take the whole assembly to the shop and have it ballanced and checked out.

here are some more pics here
http://www.trinitysmustangs.com/front_joint.htm

Ozsum2 · Nov 4, 2004

That ain't right. The bearing cap should be out against the clip.

bnickel · Nov 4, 2004

Ozsum2 said:
That ain't right. The bearing cap should be out against the clip.

exactly, you have the wrong u-joint bro

streetgrande69 · Nov 5, 2004

bnickel said:
exactly, you have the wrong u-joint bro

ok, help me find the right set-up

yokeu-joint is from a 89 mustang with an aod, what universial do i need?

Route666 · Nov 5, 2004

Does the U-joint fit flush in the driveshaft?

I ask because if it is too small for the DS and the yoke, you'll need a different size I guess, but if it fits properly in the DS, and not in the yoke, you'll need a different yoke, or change the DS.

302 coupe · Nov 5, 2004

don't even bother with trying to go by application. Take some measurements with a dial caliper and note style/location of the lock rings. Then go to a knowledgeable parts store and match it up with the measurements in the back of their u-joint book.

JB66 · Nov 5, 2004

From the previous thread...
FYI also...
Some AOD/E's and all the 4R70Ws also have larger diameter output shaft bushings & larger diameter yokes. All models have the same 28 spline output shaft profile, so small bushing tail shaft housings can be swapped on from any model, including from an AOD. This is also the same as C-4 transmissions which makes swaps easy.

Ozsum2 · Nov 5, 2004

bnickel said:
exactly, you have the wrong u-joint bro

Not me. HE!!!

ForceFed70 · Nov 5, 2004

Don't bother replacing a yoke or DS if they arn't the same width. They make adapter U-joints just for this reason. Very common in 4x4 applications.

Clark · Nov 5, 2004

That picture scares me! I agree that the joint should have come apart, you are fortunate. When I switched from a FMX to AOD, I broke down and purchased a yoke from National parts that accepted my stock u-joint

streetgrande69 · Nov 5, 2004

Clark said:
That picture scares me! I agree that the joint should have come apart, you are fortunate. When I switched from a FMX to AOD, I broke down and purchased a yoke from National parts that accepted my stock u-joint

i agree, it maybe should have came apart, i'm lucky. well, its at the driveline shop getting balanced and hes gonna put on Spicer u-joints so i can toss the napa brand u-joints.

all i've read on the aod swap, i never remember reading about the front yoke being special, just a typical aod yoke and joints, it it was a surprise when i found that i needed something special. anyway just more info for my swap page on my site i guess.

streetgrande69 · Nov 5, 2004

all better now, new spicer u-joints and completely balanced, $150 later. thanks to san diego drive line.

Route666 · Nov 6, 2004

Sweet, give us a report on how it drives.

yoke/universial pics....is this right?

streetgrande69

Ozsum2

New Member

bnickel

streetgrande69

Route666

Active Member

302 coupe

JB66

New Member

Ozsum2

New Member

ForceFed70

That's why they call it "dope"

Clark

streetgrande69

streetgrande69

Attachments

Route666

Active Member

Similar threads

yoke/universial pics....is this right?

New Member

Active Member

New Member

New Member

That's why they call it "dope"

Attachments

Active Member

Similar threads

Privacy & Transparency

Privacy & Transparency