Your Blower Combos

mbw1979 · Oct 28, 2006

03 GT 5 speed

I like this posting. Am I the only one who made big power with a vortech? I also have the anderson methenol injection kit too which added room for a lot more timing.

Vortech SQ 5 1/2 lbs of boost 380 rwhp 379 rwtq
8 1/2 lbs of boost 437 rwhp 421 rwtq - on a 98 degree day

Stock Block. The tuner could pull more power but was afraid it would break. He was right when he warned me, I got to greedy and it lasted 6 hours because the tune was too lean.

The car right now has a fully forged and balanced bottom end being put back together. I am going for the 500 rwhp

C&L intake
80mm sct mafs
Anderson power pipe
1 5/8" long tube headers
BBK shorty off road h-pipe
FRPP side exhaust
3:73 gears

green_fow_six · Nov 16, 2006

MMR mod 900 forged shortblock
MMR stage 2 heads
FMS Eaton M112 supercharger with 3.3" pulley 8#?
90mm Ligntning MAF
75mm Accufab TB
K&N FIPK
42lb injectors
FMS shorty headers
SLP O/R X
Saleen/Borla Cat-back
SCT tune
363.97 rwhp 354.11 rwtq with crappy CA gas

over 320 ft/lb of torque at 2500 rpm is fun!!

the98stang · Nov 17, 2006

mbw1979 said:
I like this posting. Am I the only one who made big power with a vortech? I also have the anderson methenol injection kit too which added room for a lot more timing.

Vortech SQ 5 1/2 lbs of boost 380 rwhp 379 rwtq
8 1/2 lbs of boost 437 rwhp 421 rwtq - on a 98 degree day

Stock Block. The tuner could pull more power but was afraid it would break. He was right when he warned me, I got to greedy and it lasted 6 hours because the tune was too lean.

The car right now has a fully forged and balanced bottom end being put back together. I am going for the 500 rwhp

C&L intake

80mm sct mafs
Anderson power pipe
1 5/8" long tube headers
BBK shorty off road h-pipe
FRPP side exhaust
3:73 gears

Holy GAWD 380WHP w/ 5.5 psi? That's seems kinda high for a SQ.

This might be a stupid question, but what is the "largest" pully that would produce the least amount of boost (or maybe larger pullies produce more boost). Would it be possible to run like 5psi with a P1Sc, vortech SQ, Novi2000, etc? I'm asking because I'm thinking about a SC but I already have the juice lol. And I know my car can only handle like 400WHP. I keep wishing I should have waited for the SC instead of the juice, because now I want the power there ALL of the time . But if I have n2o AND a SC, I could drop in a VT engine when the stocker gives, and then make OUTRAGOUS power.

Also, can someone explain to me why centrifugal blowers produce boost later in the RPM's compared to a Roots? I don't understand how that happens when both use the crank pully etc to spin the compressor?

Anyway, thanks for any info guys.

Tanner

TacBear · Nov 19, 2006

My combo is in the Sig!!

kyles03sonicgt · Nov 23, 2006

the98stang said:
Holy GAWD 380WHP w/ 5.5 psi? That's seems kinda high for a SQ.

This might be a stupid question, but what is the "largest" pully that would produce the least amount of boost (or maybe larger pullies produce more boost). Would it be possible to run like 5psi with a P1Sc, vortech SQ, Novi2000, etc? I'm asking because I'm thinking about a SC but I already have the juice lol. And I know my car can only handle like 400WHP. I keep wishing I should have waited for the SC instead of the juice, because now I want the power there ALL of the time . But if I have n2o AND a SC, I could drop in a VT engine when the stocker gives, and then make OUTRAGOUS power.

Also, can someone explain to me why centrifugal blowers produce boost later in the RPM's compared to a Roots? I don't understand how that happens when both use the crank pully etc to spin the compressor?

Anyway, thanks for any info guys.

Tanner

Dude, you and I both are in exactly the same postion. I got the juice a while back and love it when the bottle's full, but I hate worrying about bottle pressure and such, and when my car is n/a its just doesn't have any balls compared to it on the juice. I've decided to get a blower this winter, I already have 1000 saved away and I'm waiting on my big tax return. I'm considering a kb or a mph vortech kit...

01KBGT · Nov 30, 2006

KB 1.7L 9LB Intercooled
36LB Injectors
KB BAP
Accufab 70mm Throttle Body
K&N Drop in
3:73's

1BadAzzGT · Dec 3, 2006

Here is a link to all of my mods, etc

Chris00GT · Dec 3, 2006

Vortech V2-SQ with 3.12 pulley
Custom Power pipe
Procharger 3 core intercooler with custom piping
Vortech mini race bypass and Mondo Maxflow race bypass
Bullitt Intake with stock throttle body
42lb injectors with twin focus fuel pumps
Pro-M Univer mass air meter
HP 292S blower cams
Stock short block with canton windage tray
MAC LT's with 3" collectors
Dr Gas 3" X pipe
Dynomax Ultraflow cat-back
Kauffman Motorsports SCT tune

531rwhp and 463rwtq SAE on a Dynojet

Kingro Cobra · Dec 5, 2006

Another shout out from us Canadian guys

Here's my mods the car was finished in October and i drove it for 3 weeks before the snow set in up here but it was silly fast and i had a safe tune as i had a bit of bad luck when i first installed everything:

VT Engines forged short block
Diamond pistons (9.8 compression)
stock cam
Vortech S-Trim (3.1 Pulley)
SHM a/a intercooler
Procharger 1.5" Race bypass valve
AFM Power pipe
Bassani Side exhaust
Hooker Long Tube Headers
SCT CHip tuned by Matt(Mustang Shop)
60lbs injectors
90mm LMAF (with MAF extender)
Hotchkis upper/lower control arms
Koni red shock front/back
4:10 gears

I see about 12psi of boost on a good air day

my numbers:

450/365

Should see low 11's no problem if i get traction

Ryan - Saskatoon(Canada)

stroked4.6 · Dec 6, 2006

Here's my set-up...

4.6L stroker kit >> 5.0
Vortech V-2 SQ w/ Aftercooler
Patriot Stage II Heads
Comp Cams 270
42lb Injectors
90mm MAF
BBK Long tubes
BBK H-Pipe w/ cats
Flowmasters
BBK 75mm T/B
BBK Plenum
A/C Delete
FRPP 3.73
SCT Tune (Mail Order)

Not sure what my numbers are yet since i am still breaking the new setup in. Well after the winter with the new TKO ill know for sure. Ill be heading to Mustang Magic. Anyone tune their car there?

1fast03pony · Dec 7, 2006

stroked4.6 said:
Here's my set-up...

4.6L stroker kit >> 5.0
Vortech V-2 SQ w/ Aftercooler
Patriot Stage II Heads
Comp Cams 270
42lb Injectors
90mm MAF
BBK Long tubes
BBK H-Pipe w/ cats
Flowmasters
BBK 75mm T/B
BBK Plenum
A/C Delete
FRPP 3.73
SCT Tune (Mail Order)

Not sure what my numbers are yet since i am still breaking the new setup in. Well after the winter with the new TKO ill know for sure. Ill be heading to Mustang Magic. Anyone tune their car there?

I recommend Realspeed Automotive in Bohemia for tuning

www.realspeedautomotive.com

fastback brian · Dec 9, 2006

99 GT
Procharger f1a, 3.85 pulley
8 rib with stock truck crank pulley.
20+ psi
bullitt intake and t-body
stock fuel rails with 55# injectors.
STOCK heads - STOCK cams.
9.5-1 compression built shortblock.
mac exhuast, long tubes, prochamber and flow paths.
twin focus fuel pumps, stock fuel tank, basket and lines.
stock t-45, driveshaft and 4.30's.
17* timming , 100 octane gas.
511rwhp 485 rwtq.

this is my daily driver, engine is old and beat up pretty good, now on its fourth blower and has had oxide on it, NO dyno numbers on the bottle. I may be swapping out this stock setup for a worked SVO head/intake setup with blower cams and a fresh shortblock.

Vortang03 · Dec 16, 2006

I got a..
Vortech SQ Tirm-8 psi
SCT hand held
Boost Pipe
MGW Short Throw
Magna Flow X-pipe
Safe tuned and non i/c-362 hp/360 tq
I/C and pulley SOON!!!
:SNSign:

invertmast · Dec 23, 2006

OLD Setup:

96GTS w/ Stock 04GT bottom end and heads
Crower stage 2 S/C Cams
FRPP Shorty Headers
Mac O/R H pipe
FRPP 4.10's
SVO/FRPP Roots supercharger @ 6psi
90mm lightning maf.
Stock intake and airbox
stock throttle body
weld in 2 chamber flow's
Custom Tune by Amazon Racing in a X-cal 2
255lph HP intank pump
30# injectors
Kirban Fuel Pressure Regulator
Custom EGR Delete kit (made it myself)
NGK TR6 plugs @ .035"

422rwhp 402 rwtq
421rwhp 402 rwtq (back to back runs)

Gearbanger 101 · Dec 23, 2006

invertmast said:
OLD Setup:

96GTS w/ Stock 04GT bottom end and heads
Crower stage 2 S/C Cams
FRPP Shorty Headers
Mac O/R H pipe
FRPP 4.10's
SVO/FRPP Roots supercharger @ 6psi
90mm lightning maf.
Stock intake and airbox
stock throttle body
weld in 2 chamber flow's
Custom Tune by Amazon Racing in a X-cal 2
255lph HP intank pump
30# injectors
Kirban Fuel Pressure Regulator
Custom EGR Delete kit (made it myself)
NGK TR6 plugs @ .035"

422rwhp 402 rwtq
421rwhp 402 rwtq (back to back runs)

Wait a minute,you made that kind of power with a non-intecooled FRPP blower at only 6psi......and through stock PI heads no doubt?!?

Sounds like I need to get me a set of Crower Cams.

invertmast · Dec 23, 2006

forgot to mention, that was on a mustang dyno.

but 2 months prior to those numbers, the car put down 306/366 on a dynojet w/o the 90mm MAF, cams and custom tune, and it had a REALLY bad vacuum leak, and a dead front O2 sensor.

so i think the true numbers were around 400/400 b/c my buddy w/ an 03 cobra w/ echaust and 2.8 upper pulley was slower than this car. lol

mklovell · Dec 24, 2006

My recently installed P1SC.....

See below (tuning on Mustang Dyno)

lgndracer · Dec 26, 2006

Info in sig.........

mbw1979 · Dec 30, 2006

kyles03sonicgt said:
Dude, you and I both are in exactly the same postion. I got the juice a while back and love it when the bottle's full, but I hate worrying about bottle pressure and such, and when my car is n/a its just doesn't have any balls compared to it on the juice. I've decided to get a blower this winter, I already have 1000 saved away and I'm waiting on my big tax return. I'm considering a kb or a mph vortech kit...

I couldn't believe the power the car made with little boost either. but then again it didn't live that long either. The tuner said it had to do with my exhaust being so free flowing and the methanol injection.

I to came from being nitrous car. I would go with a centrifugal SC over a roots for easier drivability. Roots delevelops boost much faster and peeks faster than a centrifugal. the centifugal keeps building as you rpm builds. I have a street car and traction is a problem. I like the boost coming on later. With having a gear in the rear end, the car revs easy, so developing the boost is not problem. From 4-6200 rpm's the car is a monster. But if your just cruising, it doesn't jerk you all around. I guess it depends on what you want. If you want a stump puller off the line, go with a roots. But if you like that screaming top end charge, go with the centri.

Procharger is more costly intially, but seems to be the best to make power. Vortechs you have to add this and get that which adds up after awhile. It has everything you need right off the bat. the intercooler and the way they do there geas develops more boost quicker than vortechs. But i am happy with my vortech, from a 40 roll it is hard to beat.

My car is just finished, I have a forged, balanced bottem end and blower cams. The builders goal is 525rwhp safely with a custom tune.

fast97gt · Jan 9, 2007

not boosting yet but will be soon i cant wait after reading all these post, koodd its gonna be nice

Your Blower Combos

mbw1979

New Member

green_fow_six

the98stang

Active Member

TacBear

kyles03sonicgt

New Member

01KBGT

New Member

1BadAzzGT

Chris00GT

Kingro Cobra

New Member

stroked4.6

Member

1fast03pony

Member

fastback brian

Vortang03

New Member

invertmast

Gearbanger 101

Straight Outta Locash

invertmast

mklovell

New Member

lgndracer

New Member

mbw1979

New Member

fast97gt

Active Member

Similar threads

Your Blower Combos

New Member

Active Member

New Member

New Member

New Member

Member

Member

New Member

Straight Outta Locash

New Member

New Member

New Member

Active Member

Similar threads

Privacy & Transparency

Privacy & Transparency