explorer pieces

undercnstrction

New Member
Nov 10, 2009
312
0
0
i know the v-8 ford explorer uses the same intakes as the cobra, but did i read correctly that the v-8 ford explorer has the same heads as the cobra???

here's part 2: are those heads the same as GT40 heads?
 
I answered as best as I could in your pm, but to sum it up for anyone else that doesnt know. the iron gt40 heads are the same heads that are on the 93-95 cobras but with different valve springs. change the springs and they are a direct bolt on. the gt40 p heads also require a spring swap along with the addition of p specific headers to allow access to the spark plugs.
 
There is a difference between the explorer GT40's and the 93-95 Cobra GT40's...aside from the valve springs.

The explorer versions lack the provisions for the air pump tube that connects to the rear of the heads.
 
There is a difference between the explorer GT40's and the 93-95 Cobra GT40's...aside from the valve springs.

The explorer versions lack the provisions for the air pump tube that connects to the rear of the heads.

another stupid question......can you explain what "air pump" you're referring to? i'm trying to think what was on the back of the heads when i took them off the motor and it's not clicking in? does this mean that the heads off of an explorer cannot/should not be used?
 
the reason i'm asking all of the questions about the explorer setups is because i have the chance to pick up 2 sets of v-8 explorer heads and intakes for a pretty good price. the greedy capitalist in me is trying to determine if i can flip the pieces and funnel the money into my own project.

hope this idea doesn't offend anyone :nice:
 
another stupid question......can you explain what "air pump" you're referring to? i'm trying to think what was on the back of the heads when i took them off the motor and it's not clicking in? does this mean that the heads off of an explorer cannot/should not be used?

The "air pump" he's talking about is your smog pump. It should be the bottom pulley on the passenger side. It has two tubes that come out of it... one tube goes to the back of your heads, and the other tube goes to your midpipe.
 
unless you are going to use them for your own car I would pass. now is not a great time to try and flip parts. I have several explorer top ends that have been in my shed for over a year now b/c no one wants to pay what they are worth and then pay to have them shipped on top of that.
 
Explorer stuff is dirt cheap today. Maybe 5 years ago you could flip them, but with the amount of 5.0 exploders in yard now, they are plentiful and cheap.

I'm actually in the middle of buying one off CL for $75 complete just for the lower intake alone.
 
Explorer stuff is dirt cheap today. Maybe 5 years ago you could flip them, but with the amount of 5.0 exploders in yard now, they are plentiful and cheap.

I'm actually in the middle of buying one off CL for $75 complete just for the lower intake alone.


if you are paying $75 for the lower, i can get the upper AND lower for less than you are going to pay for just the lower.

i'm seeing GT40 heads going for anywhere from $150-300 on corral. the ones i'm looking at are less than that.
 
if you are paying $75 for the lower, i can get the upper AND lower for less than you are going to pay for just the lower.

Nope....$75 for both. I could prob haggle a little lower, but the intake is clean.


Junkyard near me wanted $40, but i am too lazy to deal with getting dirty and pulling it off myself. I think they wanted $75 for the heads too. Again...it's 20 degrees out and i don't want to sit there covered in grease pulling dirty parts off and put them in the trunk of my car. There are at least 4 exploders in my hard. To me, the cost of flipping them didn't justify the labor involved...esp when i see the prices of the heads and intake falling all the time.
 
I answered as best as I could in your pm, but to sum it up for anyone else that doesnt know. the iron gt40 heads are the same heads that are on the 93-95 cobras but with different valve springs. change the springs and they are a direct bolt on. the gt40 p heads also require a spring swap along with the addition of p specific headers to allow access to the spark plugs.

negative noober!! pretty much all sbf headers will work, you just have to get creative with the plug wires.. ask mr BK_cheeze and myself.. your 93 vert had p heads with standard bbk shorties on it, and it was all good in the hood..
 
Explorer stuff is dirt cheap today. Maybe 5 years ago you could flip them, but with the amount of 5.0 exploders in yard now, they are plentiful and cheap.

I'm actually in the middle of buying one off CL for $75 complete just for the lower intake alone.

plentiful and cheap? I live in a pretty big city and hit 2 of the three biggest junk yards the other day. Scored on a TB and thats it. Seen only 2 v8 exploders and motors where gone. I must have bad luck. I am about to move to a diff state too and have credit at the yard I did go to. Guess I wont get my money if I cant find parts I need. Sucks. If the intake is $40 and I have $35 credit then its almost free. If only they had one.

This is my problem. Pay $5 @ the junk yard or buy for $200 on ebay. Screw it, if anyone lives in the Kansas City metro area needs this credit give me half the cash and its yours. I move in three weeks.
 
negative noober!! pretty much all sbf headers will work, you just have to get creative with the plug wires.. ask mr BK_cheeze and myself.. your 93 vert had p heads with standard bbk shorties on it, and it was all good in the hood..

did you have to use those ghey cut to fit plug wires? bah, flip your headers over like Mob did and put a blow dryer on there.