Torker II vs PP Typhoon

I don't think it matters anymore. Everyone proxy bids on ebay now. Not too many people sit up late at night on their computers clicking away vigorously trying to outbid people. The excitement of ebay is gone. I just set the max price I'm going to pay for something into my proxy bid and walk away from it. Last week I bid on a set of locking header bolts. The opening bid was $25 with $7 shippign, and I set a max bid of $35. They are only $44 from Summit. Some idiot bid over $35 for them. So he's going to pay as much money on that chancy ebay deal vs just buying a sure thing new from Summit.

Kurt
 
The_Mustang; said:
I'm sure Chris was probably on some kind of budget when he built his motor and the Typhoon has a very nice appeal to it when you compare it's 400$ pricetag to that of, say, a Trick Flow R intake at 700$.

just my .02
heh, i was on a budget, but then i blew that out of the water with all the polished crap.

but i got this for a good price on corral.
 
Are you nuts! It is because of that long runner intake that we could take a stock Fox 5.0 and run in the 13's with it. It's because of that long runner intake (and the heads of course to a certain extent) that we could put 3 or 4 car lengths on a equally equipped Z28 without a problem.

The long runner intake design is perfect for a street driven 302. A stroked out Windsor is a completely different animal. It requires much more volume of air to feed it.

I'm sure Chris was probably on some kind of budget when he built his motor and the Typhoon has a very nice appeal to it when you compare it's 400$ pricetag to that of, say, a Trick Flow R intake at 700$.

just my .02

Maybe I am but there is a reason why people switch to a carb intake and run faster in the 1/4. The long runner intake is good for idle to about 4,500. Then again I have always run single plain intakes on all my carbed cars instead of the dual plain intakes that everyone else says is much better for the street.

I just don't like the design of the stock long runner mustang intakes. The ports have several twists and turns not to mention uneven flow distribution. The aftermarket long runners are much better but it's still a compromised design IMHO.
 
The long runner intakes make the car run better, and consequently give it better gas mileage. Most fuel injected cars have long runner intakes. People swap to carb setups because they are cheaper, and easier to tune.

Kurt
 
The long runner intakes make the car run better, and consequently give it better gas mileage. Most fuel injected cars have long runner intakes. People swap to carb setups because they are cheaper, and easier to tune.

Kurt

I have never noticed my carbed cars running that bad or having a unstable idle before nor have I ever noticed a torque deficiency. I personally think that the fuel injection itself is where credit is due for all the things you mentioned not the long runner intake.
 
If a carbed car is setup correctly of course it CAN be a nice ride. The problem is, however, that given slight weather fluctuations some carb setups become dogs. Ever see 2 lane blacktop? guy was changing jets the whole movie. Screw all that mess.... turning this screw, adjusting this and that. Nah, not for me.

And for the post about the long runner intakes being the worst thing, you have to be specific on that. Yes, the stock unit leaves alot to be desired, but you can't throw that in with the likes of Edelbrock, Holley, TFS etc... I personally had a car with an Eddy performer and it'd pull all the way to 6k rpms just fine. And I could drive it winter, summer, rain, shine without adjusting my jetting or choke or anything! To me, people who change EFI stang's into carb'd cars are just too lazy to learn EFI plain and simple.

And just remember, if carbs were SO much better, then why the hell did they invent fuel injection?
 
If a carbed car is setup correctly of course it CAN be a nice ride. The problem is, however, that given slight weather fluctuations some carb setups become dogs. Ever see 2 lane blacktop? guy was changing jets the whole movie. Screw all that mess.... turning this screw, adjusting this and that. Nah, not for me.

And for the post about the long runner intakes being the worst thing, you have to be specific on that. Yes, the stock unit leaves alot to be desired, but you can't throw that in with the likes of Edelbrock, Holley, TFS etc... I personally had a car with an Eddy performer and it'd pull all the way to 6k rpms just fine. And I could drive it winter, summer, rain, shine without adjusting my jetting or choke or anything! To me, people who change EFI stang's into carb'd cars are just too lazy to learn EFI plain and simple.

And just remember, if carbs were SO much better, then why the hell did they invent fuel injection?

hehe, I'm sorry the carb reference was just for the style of intake not the carb itself. I agree that EFI is nice and I like my efi but people are saying that a long runner intake will give you better driveability, gas mileage, and idle over a efi converted carb style intake. The EFI long runners limit rpm's. Sure the aftermarket has made them much better but I think the carb style intake will still accelerate better.

The only time I ever needed to adjust on my carbed car was in weather extremes and even then it wasn't ever a dog in fact I never touched it. I just drove it and enjoyed it. It still was very responsive quick and fun.

Funny thing is everyone probably thinks I'm some old school guy but I'm 30 and my first car was a 70 mustang fastback with a australian headed 2v 351C. The car had a single plain intake (a old holley street dominitor), 750 holley dp, 4v 2.19, 1.71 size valves, and a lunati bracket master cam with .562in .588ex lift 234in, 244ex duration at .050. The car was not the fastest but it sure was fun. It surely did not lack torque.