Search results

  1. Darek78

    Quick A/C compressor and PAG oil .....

    Hey guys i need some quick help :D My old a/c compressor locked up and i got a new one and i need to know how much of Pag oil to put in the new one :shrug: Some one told me to dump the oil from the old one to see how much it comes out and then put the same amount back ....but my old one is...
  2. Darek78

    Quick valve covers help

    Hey guys what valve covers aluminium i can get from summitracing that will work and clear my rockers i have Ede Performer intake with 1/2 spacer steeda 19 cam Afr 165's heads and crower 1.6 roller rockers Stud mount ??? :shrug: thanks Derek.N
  3. Darek78

    oil question

    Hey guys can some one give me a answer what oil was recommended by factory for 95 gt's i dont have owner's manual but i would like to know is it 5w30 or 10w30 thanks
  4. Darek78

    Oil seperator fitting size .....

    Ok one quick question??? I got a Campbell Hausfeld in line filter i need a threaded side fitting size .... are they 1/4 inch or 3/8 threads ??? Thanks Derek
  5. Darek78

    Were can i get ......... ??

    Hey guy when i put my intake on i forgot to put the little breather under the grommet for the pvc valve :bang: my problem is that i put some rtv on the grommet and now when i tried to remove it it got riped :mad: i went to Auto zone and R&S and they don't have it they can't even get it for...
  6. Darek78

    I need some info (intake swap )

    Hey guys i just need some info on the intake swap ..... im going to replace my cobra with a ported Tmoss edl preformer intake to fit my afr's 165 heads ... my first question is how much torque to apply to the bolts on the lower intake ?? :shrug: second question is what gaskets to use...
  7. Darek78

    I got my AFR 165cc installed and Dyno

    Hey Guy's finally got my AFR heads from Kevin from K's Kustoms and got them installed on the car after the install we put the car on the dyno and this is what we got then we added few degrees of timing and the results are then we took 1 degree of the timing and this is the final result...
  8. Darek78

    Wired disappearing of spark (Help)

    Hey guys my problem is starting to drive me crazy :mad: From time to time my car cranks but dosen't start i changed all the parts TFI module ,coil ,cap rotor wires (yes the fuel pres is there )and still i get this plus some funny thing is going on with the power to the coil i get power on the 2...
  9. Darek78

    Afr 165cc Need advice and have some Q

    Hey guys i would like some of you to help me out :D I'm getting ready to place n order with Jegs, for Afr heads. I'm going with stud mount because i see most of the people like them better over pedstal mount. What would be the best Gaskiet set to get for top end any part numbers ?????? :)...
  10. Darek78

    turning off egr with tweecer wich scalar is it ????

    hi guys i would like to turn off my egr with tweecer i have 3 egr settings in scalar 1. Egr multiplier factory says 1 2. Egr part throttle adder factory says 0 3. Egr system type factory says 0<------ Is this the one that i have to change to number 2 to disable ?????????????????? sory for...
  11. Darek78

    i have a Question about saving files in CalEdit ???

    Hey guy's i need a answer on this Let's say i take a new fresh copy of TM4O.ccf then i go to Scalars and chenge my fan and idle after that i click on Functions and select maf transfer so i take my flow sheet put the numbers in and now if i click directly on top save file will this save my...
  12. Darek78

    I need help !!! Puting a flow sheet into Tweecer

    Hi guy's I need some help entering my Maf flow sheet intu a tweecer i tryed to do something but no luck :bang: I have no clue how to do this at all :shrug: I need some one to make me a print screen of it i did use the search the Tweecer web site and i did not find anything that will help me...
  13. Darek78

    What can cause on even idle??????

    Hi guy's i have some problem's with the idle on my car , when i start it it runs fine for a while and then you can hear a slight jump in idle not to much and then after 3 sec get's back to normal and every 30 to 20 sec of idle does this any ides????????? :shrug: it's not ideling even all the...
  14. Darek78

    What's wrong with my car !!!! (Help)

    Hey guys i have a weird problem with my car and i can't figure it out what's wrong with it need you'r help :shrug: ok first thing in the morning when i start the car has idle surge but it goes away.When the car get's to normal opetation temp it runs fine but the problems start's here when i...
  15. Darek78

    Tweecer Guy's... come in

    Hey guys i just need to make sure that my swich is working the way it should what i have read in the tweecer manual is when you put the possition 5 on the swich that turn's off the tweecer and iw you disconect thheom that wire it the same thing ating in 5 position And now Can any one try tis...
  16. Darek78

    just a test

    testing Derek.N
  17. Darek78

    Mr GRADY.........and all (Tweecer)

    Ok i just got my 24lb injector's installed and i got a C&L 73mm and i put in a calibrated tube orange color :)( using a stock maf sensor) My Q is do i have to change injector slopes on my Tweecer R/T or i can leave it on the 19lb one's????? or it would be better to change them :shrug: does...
  18. Darek78

    How does flowmaster sound with X-pipe ??????

    Hey guy's i would like to know how the flowmaster's would sound with X pipe ??? Right now i'm running BBK shorty's and mac H pipe with cat's and flow's and i gor rid of my emision stuff and i'm looking to het something cat less and i was thinking X pipe ??? thanks Derek.N
  19. Darek78

    No polution pump!!!! with cat's on ?????????( help)

    Hey guys i just pick up my car from the shop :) I had a new cluch put in (Center force) I notice that problem before but now it's geting worse and worse the car has no power it's like somthing holding it back and somtimes i get like back fire if you can call that like 2 or 3 poping sound...
  20. Darek78

    Tweecer......

    Tweecer...... (grady) Hi guy's ok i don't know if i'm writing my tweecer the right way so i need you're answers ok what i did is i went on the caledit went to Scalars made some changes and later changed my position to nr 1 and pressed write to tweecer after it was complete i starded my car...
Top Bottom
Back
Forums
Menu