Search results

  1. HP Addiction

    A/C

    Which port do I use to recharge my A/C/? I see two ports with black caps and one with a green cap. I know it needs to be filled on the low pressure side, but I dont know which one that is.
  2. HP Addiction

    New crush washers??

    I posted a thread a couple days ago regarding new SS rear brake hoses. I just received them today but they did not come with crush washers. Can I use the old ones?
  3. HP Addiction

    brake hose question

    I have a 2000 mustang GT and just ordered the rear Cobra Brake upgrade kit. Do I need to use cobra rear brake hoses or will the rear GT hoses still fit?
  4. HP Addiction

    Wiper problem

    I'm having a very difficult time figuring this problem out. When I turn my wipers to the delay/intermittent setting they get stuck half way up and wont move. The high and low settings work fine. However, even on the high and low setting the wipers stop wherever they are when the switch is...
  5. HP Addiction

    Where to install cylinder head temp sender

    Hi all. This is my first post in the 5.0 forum. Hope you can help me with this. I'm installing an electric autometer cylinder head temp guage on my brothers 90 GT. Would you happen to know where the sender can be tapped into on the head? Thanks!!!
  6. HP Addiction

    King Cobra

    It's about time for a new clutch and I need some opinions. I was considering a King Cobra? Is anyone running this. If so, how do you like it compared to stock.
  7. HP Addiction

    New Clutch?

    I have noticed over the last few weeks that my clutch is engaging at the very top. I tried adjusting it (pulling up on the peddle) with no avail. I have about 81k on the stock clutch. Is this a clear sign that it is worn or could it be something else? Thanks
  8. HP Addiction

    test

    t
  9. HP Addiction

    Need CAMS

    Need some advice on Cams. I think this is the next logical mod aside from a blower. Looking at my current mods, which cams do you recommend for optimal HP gain without loss of low end torque and driveability? THANKS!
  10. HP Addiction

    Dyno tune results are in!

    Had the car Dyno tuned yesterday. Very happy with the results. :) RWHP =258.7 RWTQ=294.1 Mods are in signature.
  11. HP Addiction

    Please help with 1700 rpm miss!

    Need some help with a 1700-2000 rpm miss/buck. Car runs smooth above the aformentioned RPM and at WOT. I can feel the miss when reving the car in N or when crusing under a load. Any ideas? Thus far I have changed the COPs and backed down the timing a few degrees. No change :shrug:
  12. HP Addiction

    Timing question

    I have been running my Steeda TA at 15* for about 3 years now. It definitely "feels" like it I have gained a few HP and TQ. Overall, I am happy with it. Now, I am considering a Diablo tuner. I have heard that the timing advance is better if you use the predator vs. a TA. Can someone explain how...
  13. HP Addiction

    Next Mod?

    With $500-1000 to spend, what would you recommend for my next mod? Not sure which way to go. Below are my current modifications. THANKS
  14. HP Addiction

    OBD-II Scan tool

    I was looking into purchasing an OBD-II scan tool. Does anyone have any recommendations? I want something that has the capability to read all the codes, log data, and be able do things such as cycle ABS solenoids etc. Any ideas? THANKS :flag:
  15. HP Addiction

    Granatelli

    Anyone running Granatelli COP on their N/A 99+? I noticed them on a few websites but haven't heard of anyone running them. Are they worth any power, throttle response etc.?
  16. HP Addiction

    TACH install help

    I am helping my friend install a tach in his 2001 cobra. He purchased it from speedhut. The directions which suck IMO indicate that it does not require a tach adaptor. There is one yellow wire which is the tach lead. However, I am not sure how to hook it up. I assume that I may have to splice...
  17. HP Addiction

    Plug gap

    Not exactly stang related but it is a 4.6. Does anyone know what the plug gap should be on a 99 4.6 NPI motor in a crown vic. I have a set of autolite 764's. I ran the gap tool over them and they are showing .047. Do they need to be opened up more? Thanks. :flag:
  18. HP Addiction

    Please help with header install!

    My brother and I are installing Mac equal length headers on his 90 5sp GT. The driver side went on without too much difficulty. The passanger side on the other hand is a nightmare! We were finally able to pry the header and get it close to bolting up, but its is way too tight. So tight that...
  19. HP Addiction

    Dyno Tune

    I think it is time for a dyno tune. Does anyone recommend any specific shops on Long Island and know approx cost? Thanks
  20. HP Addiction

    Help with Fuel Pressure Gauge!

    No luck with this question in the 4.6 forum...Does anyone know where I can find a fitting to attach my autometer Fuel Pressure guage sending unit to the factory installed schrader valve on the fuel rail. I do not want to remove the schrader valve if at all possible, just want to adapt to it...
Top Bottom
Back
Forums
Menu