Search results

  1. N

    lower control arm question

    which is better the box or the tube looking lower control arm or are they the same
  2. N

    perfomer vs perfomer rpm differance

    whats the differance between the two . i want one of them but later down the line i dont want too have to change and spend more money. will an rpm 2 be good for a stock motor i have 3.73 gears cold air induction full exhaust chip a/c delete, pulleys how much horsepower we talking about if i...
  3. N

    mesh screen under PCV valve in lower intake

    reply late model restoration supply part number lrs-6631a page 87 fits 86 to 95
  4. N

    water pump question

    reply is it normal for it to read over half on the gauge when i used i 160 stat it barely went up. now i got 180 stat and it reads over half already change a crap load of parts will a new water pump run it cooler
  5. N

    water pump question

    will a high flow water pump run my engine cooler? i have a stock one in there now but i have a new radiator,180 stat, and new heater core put in last year .and it reads over half on the gauge i already switch gauges ,temp sending unit,volt regulator and i smell antifreeze after i drive, it has...
  6. N

    what is this timing question

    what the hell is a spout connection read on another thread. something to do with setting timing is it like mufflers bearing or im i just stupid
  7. N

    Fuel Door bolt size...???

    reply i got 5/16 bolt size on the head
  8. N

    water pump question

    does a high flow water pump actually keep the engine cooler. is it better then a stock one. mine leaks a little on top where that little hole is not sure if that opens or what. should i buy a summit high flow water pump is it worth it
  9. N

    spray at psi need help

    what psi do i need do spray primer at not sure
  10. N

    primer mixture/lackure

    im priming the mustang what mixture of primer and lackure thinner do i use i got a gallon of this primer but dont no what to mix it at
  11. N

    sandblasting help

    what grit paper do i use to get down to bare metal without screwing up the piting the metal. im tired of using peeler its taking me 3 cans of that and it seems im not getting anywhere :mad:
  12. N

    best underdrives for 86 w/serpentine

    pulleys im running march on my 86 the only problem finding a belt to fit because of the crank pulley is smaller. not bad i think i would use bbk next time though
  13. N

    rear gear whine please help

    had a guy install my 373 gear after a year my buddy told me the whine got worse. i cant hear it that bad because i got dump exhaust . will this whine hurt me or cause damage if not i will still drive it but if it brakes something i screwed. tight on money. its a ford motor sport gear i watch...
  14. N

    what to do next need advice

    not sure if i should do motor or supsension. ialready have 373 gear, full exhaust, subframe, cold air induction, rad, 180 stat ,hyper chip, pulleys ,a/c delete., want to get upper and lower typhoon intake but not sure if its good or i want upper lower control arms its an 86 mustang i dont...
  15. N

    Clutch Quadrant

    im using im using steeda i like it no problems make sure its tight through the clutch fork and in where the cable sits under the black box by the trans i used two bolts because my cable came loose and got hung up on the quadrant and started to cut the cable but i like the steeda
  16. N

    cooling system problem need help anybody

    reply i think its the gauge going to the junk yard today to get one . i already changed the cvr could be the stat dont know i will try to ground the sending unit but the only two gauges are oil and temp rest are fine :bs:
  17. N

    cooling system problem need help anybody

    ok did that i could put my finger in the rad cap its not even hot it push the antifreeze into resovior bottle
  18. N

    cooling system problem need help anybody

    reply please when i touch the rad cap its warm but not overheating like the gauge says ran a 160 stat . ran cold but never over heated like the gauge says now
  19. N

    cooling system problem need help anybody

    cant understand wtf the problem is new waterpump/temp sending unit/ new rad /constant volt regulator 16 psi cap for rad/ 195 heavy duty stat. when driving the temp and oil press go up almost to hot but rad cap is cool. could it be engine temp sensor or ect be bad. how about rad cap or the...
  20. N

    Anti - ricer stickers

    i want a sticker to i want to show my hatred damn it :mad:
Top Bottom
Back
Forums
Menu