Search results

  1. S

    New Dyno #'s and a few ?'s I can't stop modding and need help

    i would save the money and keep the 2v set-up you can make good power with out motors . this combo works well forged shortblock (mmr,dss,mph) all have nice blocks up the disp. to a 302 meth is ok but simple is always better. i would just get a good intercooler nice set of heads and...
  2. S

    recommended blow-througth maf

    ok guys i am collecting my parts to finish off the power side of the car before i start on the body what blow-througth maf meter do you guys recommend atm i have the folloing parts waiting to be installed on the car paxton fmic 60# injectors vortech-mini race bypass 8-rib 2.95...
  3. S

    Sell my Vortech and get a KB or not? HELP!

    yea true but the effects is the same how often do u race at 2000 rpms lets not get to technical here the out come is the same and drivability of the centr-car is fine with a lot less traction problems :nice:
  4. S

    500rwhp how-to write-up w/ sq-trim

    question guys besides the cobra duel pumps and boost-a-pump and 42lb injectors what other mods to the fuel system did you have to do to get to 515-598 range i am trying to keep the cost down a little rigth now .... i will upgrade the fuel line to -8npt and i was thinking fpdm only if i...
  5. S

    Sell my Vortech and get a KB or not? HELP!

    yea if you have a blower man just build around it .... it will cost less and if you drop some lower gears 3.73 or 4.10 in there that will more then make up for the low rpm boost.. you said you even put in pistons to work with the vortech.. just up the boost man and dont look back believe me...
  6. S

    500rwhp how-to write-up w/ sq-trim

    ya i would have maybe done things a little differnt if i could start over.... when i was making 371 on 8psi all stock motor i was using the tune i got from mph. with a tune and a little more boost i could have hit 400. with 2v i think you have to work a little harder to get good power out...
  7. S

    500rwhp how-to write-up w/ sq-trim

    the shortblock is just to hold the power not going to get any power from that since i did not go to a 302 and my cr dropped a little from 9.1 to 8.7 or so with every thing else being the same i jumped from 371 to 446 just with the heads and camms only thing left to do is up the boost and...
  8. S

    500rwhp how-to write-up w/ sq-trim

    yea i have been following your progress jive for some time.. at what point did you need to up grade your injectors i have 42lb atm also i have the cobra tank and pumps and bap trying to save some money i modified my list a little going to see how much i can do on a 6-rib set-up 10%...
  9. S

    500rwhp how-to write-up w/ sq-trim

    ok have not gotten to my goal yet ordering a few more parts should get me there 8-rib pulley kit 10% over drive crank 2.70 8-rib pulley kit i have my fmic still in the boxes and i think i am going to need fpdm and 60lb injectors looking for +550rwhp and 16psi
  10. S

    need advice on 16psi set-up vortech..

    thx for the advice guys i think i am going to go with 10% overdrive crank pulley 8-rib 8-rib pulley kit vortech 2.75 8-rib blower pulley that will get me to were i need for 6k redline thxs for that calulator info. with this set up i can spin the blower alittle over rigth at 6k
  11. S

    need advice on 16psi set-up vortech..

    :shock:so you think just a pulley swap and upping the revs could get me there with out the od crank pulley hmmm i do see a few people here pushing there cars to 7k is that safe i mean even with heads and cams i was told keep it below 6.5k i was thinking if i could spin the blower faster...
  12. S

    need advice on 16psi set-up vortech..

    ok guys kinda limited on money here but i want to get 16psi out of my sq-trim this will finish me up on the motor for now anyways i am thinking A: 8-rib kit vortech w/o crankpulley 10 % od crank pulley 2.7 8-rib blower pulley -----------or 18% od crankpulley electric water pump...
  13. S

    Kenne Bell 2.1 Capable of 500hp+?

    you should have no problem seeing 500+ rwhp with the 2.1kb blower but your going to need some heads and cams for better airflow unless your going with more compression on the shortblock i cant see that helping your overall hp numbers the shortblock is more of a safety thing... 9.1 cr...
  14. S

    Supercharger vs Turbo

    i am at 446rwhp with my little sq-trim vortech @8psi that turbo kits sounds good cheap as hell .....
  15. S

    Starting the "build" thread...

    sweet man looks good .. did not know you could just pull off the casing on the blower to turn it that will save a lot of work... i will post some pictures here also once i get started on mine :)
  16. S

    need advice on blow-thought set-up vortech

    plz hit this post up blownstanggt with pictures if u can get them would love to see your set-up i will get some video and pictures of mine will start on it this saturday wish me luck..
  17. S

    need advice on blow-thought set-up vortech

    hey guys what all do i need to change my set-up to blow-throught i have a vortech sq-trim setting in my basement paxton fmic,vortech mini-bypass if i get the pmas 75mm 3" and a retune is there anything else i will need to do this set-up i am tring to finish up the motor side...
  18. S

    just got back from the track

    thxs for the advice ...... i am using 315 17" drag radials nitto 555r tires they are better then my old street tires as for my shift i am shifting around 6000rpms speed shifting but i am looking at getting a set of 15" welds and a 27-28" tire i dont want slicks because the car is...
  19. S

    just got back from the track

    ok just got back from the track here in maryland (capital raceway) and finally hit the 12's i admit i need more seat time to get my crappy 60' ft down but i am happy still 60' 1.99 1/4 mile ---12.736@117 mph sry for the missing 1/8 mile data i lost the dam slip :nonono: i also...
  20. S

    need a little advice on my vortech

    ok just got the paxton fmic in the mail also have upgrade vortech valve and a 3.12 pulley 6-rib my question is will i have to worry about slippage with this size pulley i am going to the 3.12 from 3.6 pulley.. also what kind of boost should i see with a 3.12 i am seeing about 9psi...
Top Bottom
Back
Forums
Menu