intake manifold

Hello. I have a 2001 Mustang GT. I bought it new. I’m swapping out the intake manifold so I figure I’ll swap out the plugs, etc while I’m there. I’m not sure if it would be better to upgrade to better parts than stock parts. I bought the Red EDELBROCK 22781 performance coils. Are the...

manifold

Hello all, I’m pretty new to the forum and this is my first post. I have a 2004 3.9 V6 and I swapped the upper intake manifold from a 4.2 onto it. I pretty clearly made a mistake, as my car now thinks it is at 18% throttle position (checked with live feed obd2 reader) when I’m completely off the...

I'm currently working in the installation of the Shaker Hood Assembly for my 1970 Mustang Mach 1. However, this Mach 1 has a Boss 302 engine in it. The high performance intake manifold currently installed (see pic) sits excessively high. Therefore, the Hood won't close properly. I'm looking for...

Hey guys i have a 91 fox lx and im trying to decide what intake i should run to get the best results. Its a 306 with full forged bottom end aluminum edelbrock heads b303 cam and a whole bunch of other things. I am running an intercooled p600B procharger on the car also. I have no clue the make...

Hey Guys, I am havin a NIGHTMARE with my f***ing car. I had the manifold break and i didn't want to install another :poo: plastic one so i bought this one. Now i am popping codes P0171 and P0174, lean system. Yes, i know there are sensor possibilities, injector issues, and what not, but before i...

Hi All, very new to this forum but i have read a lot and i haven't seen anything for my exact issue. about 2 months ago my intake manifold cracked (the heater hose receptacle) I tried to install an OEM part that broke on install.. The threads for the plenum literally pulled out of the manifold...

I'm new here but I have a 04 GT standard trans and my OEM plastic manifold broke at the heater hose fitting so I replaced it with a professional products typhoon intake manifold and I installed it and now the cars idle is very rough. Bouncing between 1200 rpms and 500 rpms. Thought it could be...

So, I did the intake manifold swap for my car. Went from a crappy Dorman intake for a non PI motor and put on the Ford Racing Performance Intake manifold. It was actually used and off of a 2002 Grand Marquis but same crap right. I now have a misfire. Yesterday she ran like a top! Now...

Hi Guys, Hoping for some help. Getting ready to get my vehicle approved, roadworthy (safety check) and registered and have a tight time lime to do this. Worst luck ever, removing the old temperature sensor which was in tight...as it loosening I here some bubbling and when I remove it I see a...

Hey guys, I have a 98 4.6L. Pretty solid runner with most of the essential bolt on upgrades already done. There is a small leak in the back of the intake manifold which sounds to be common. Unfortunately it leaked down and killed my starter solenoid but that's another story completely. I am...

Some may already know but Holley has stepped up and brought out their Hi-Ram series intake manifolds for the Windsor Ford.

hi guys I recently acquired an 1987 mustang lx (it is converted to mass air flow) IT has a few mods the bottom end was redone about 10k miles ago it has keith black 10.25 pistons, comp cams cam (not sure wich one)roller rocker, edelbrock performer rpm heads, 70mm throttle body, 24 lbs injectors...

Was wondering if anybody is running a ported edlebrock intake. Any noticeable gains? Who ported it? I'm thinking of having mhs port one for me since I'm getting stage 3 heads from them.

Hi everyone, i cant get this coolant temp sensor out of my manifold, broke the top of it when i was replacing my intake manifold gasket. it wont turn and i tried everything from a socket(when one fit) to vice grips. and i cant seem to get it to turn. i even heated the surrounding metal and...

This is my first post to this Website. I am building a factory five roadster using a 1996 mustang GT donor, 4.6 SOHC engine. I took my rolling chassis for it's first drive around the block this past weekend. That was a thrill. Unfortunately, there are bugs to be worked out. The radiator...

Here's the deal I'm doing PI swap and I'm modifying my PI intake to work with all the old hardware. The two sensors in the front were no problem but this brass fitting in the back is the issue. What thread size is it? And what is it even called? I can't find it anywhere. Ignore the arrow in the...