I am selling my project. Car is located in Coral Springs, FL. Car is a clean titled 1990 Original black on black 5.0 5 speed LX coupe. There is no rust on the car and it has been in a garage unused for 10 years. Custom paint job the hood is fiberglass so it looks like fiberglass tearing around the ford racing logo and it transitions into tearing sheet metal once on the quarter panels and goes down to snake eyes on each side of the car. The following is a list of parts on the car:
Cervinnis 4" cowl fiberglass hood
8.8 rear is shortened 1.5 inches on each side
9" ford ends
33 spline spool
33 spline strange 5 lug axles (new 0 passes)
3.27 gears (was for twin turbo)
Aerospace Dual caliper rear brakes (new)
Steeda double adjustable rear upper control arms
Steeda aluminum solid rear lower control arms
Lakewood 50/50 (rear) 90/10 (front)
98 mustang 5 lug conversion up front
UPR billet caster camber plates (new)
UPR coil over front (new)
Tubular kmember and aarms (new)
Manual steering rack
Billet Specialties Street Lite 15x4 and 15x10 rims (new)
Mickey Thompson 275/60 15 drag radials
Subframe connectors
Driveshaft loop
Moroso Battery Box
New carpet
New Corbeau seats
Click here for more photos here
The stock back seat I no longer have as it was going to have a rear seat delete put in after the cage. The passenger door panel has a patch missing that can't be seen when the door is shut (it sits next to the dash - see picture). I have the front seat belts and ecu wiring harness out of the car as it was going to be run with a DFI system. There is no ECU for it. I actually have 2 engine harnesses for it.
I am asking $8500
I have a 10pt Wolfe Racecraft chrome moly jig notched cage (hold and weld ) that cost 1200 new and still wrapped as it was shipped to me. Will sell with the car for an extra $700
You can email or text me at 954-465-7146
Cervinnis 4" cowl fiberglass hood
8.8 rear is shortened 1.5 inches on each side
9" ford ends
33 spline spool
33 spline strange 5 lug axles (new 0 passes)
3.27 gears (was for twin turbo)
Aerospace Dual caliper rear brakes (new)
Steeda double adjustable rear upper control arms
Steeda aluminum solid rear lower control arms
Lakewood 50/50 (rear) 90/10 (front)
98 mustang 5 lug conversion up front
UPR billet caster camber plates (new)
UPR coil over front (new)
Tubular kmember and aarms (new)
Manual steering rack
Billet Specialties Street Lite 15x4 and 15x10 rims (new)
Mickey Thompson 275/60 15 drag radials
Subframe connectors
Driveshaft loop
Moroso Battery Box
New carpet
New Corbeau seats
Click here for more photos here
The stock back seat I no longer have as it was going to have a rear seat delete put in after the cage. The passenger door panel has a patch missing that can't be seen when the door is shut (it sits next to the dash - see picture). I have the front seat belts and ecu wiring harness out of the car as it was going to be run with a DFI system. There is no ECU for it. I actually have 2 engine harnesses for it.
I am asking $8500
I have a 10pt Wolfe Racecraft chrome moly jig notched cage (hold and weld ) that cost 1200 new and still wrapped as it was shipped to me. Will sell with the car for an extra $700
You can email or text me at 954-465-7146