• Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SN95 4.6L Mustang Tech

1996 Built GT new BOV and PMAS MAF not idling

  • Thread starter Thread starter reeber
  • Start date Start date Jul 19, 2018

reeber

10 Year Member
Mar 10, 2004
574
26
38
Berlin, NJ
Jul 19, 2018
#1
  • Jul 19, 2018
  • #1
See attached picture. Could the location of where they welded the MAF be the reason it won't idle on the dyno? Full throttle is fine, but it's not consistent on idle and it's all over the place. I had the PMAS FLG-SS-HPX Mass Airflow Sensor Kit installed and the Tias BOV 50mm 11psi spring.

I have a feeling they may have installed the MAF too close to the bend in the discharge tube (Vortech SQ-V2 Trim non-intercooled) 500RWP before this setup.

thoughts? I had the pipe powder coated and all. Just didn't want to destroy the finish, order a new flange and have to re-weld at a new location after all this work, if I would end with the same result. Thoughts?
 

Attachments

  • 63512-MMS-1531516662938-attachment1-20180713_171735.webp
    314.7 KB · Views: 283

Dark04GT

10 Year Member
Apr 27, 2008
758
62
59
NC
Jul 31, 2018
#2
  • Jul 31, 2018
  • #2
I’m assuming you are running a BOV like this one: http://www.tialsport.com/index.php/tial-products/bovs/46-tialbvq

You need to run the lower supercharger spring (2psi). The higher springs are meant for turbochargers.

The lower spring psi should help leak off that excess pressure and smooth out your idle.
 

reeber

10 Year Member
Mar 10, 2004
574
26
38
Berlin, NJ
Sep 18, 2018
#3
  • Sep 18, 2018
  • #3
It’s been almost 3 months and my car is still at my tuners shop. He went through electrical, vacuum system and now thinks it may be a valve spring.

I didn’t realize how complicated engines could be to take 3 months to fix. Ugghhhh
 

reeber

10 Year Member
Mar 10, 2004
574
26
38
Berlin, NJ
Mar 17, 2019
#4
  • Mar 17, 2019
  • #4
So, it turns out that my local shop had absolutely NO IDEA what they were doing. They used HP Tuners to tune my 1996 Mustang GT (stock ECU). I come to find out after contacting 3 other shops that the tuner isn't able to tune and can only data log on my car. So, now I lost 3.5 months with the car, made a ton of unnecessary changes per the shop owner (replaced injectors, PMAS slotted MAF, blow off valve with a spring that is NOT for my setup, etc.). I spent a ton of money and now have to remove half of it. Thank god I found DGR Performance in Dilsburg, PA. He went through a ton of detail upon the review of my car. He's going to build and air to air intercooler for the Vortech V2-SQ Trim so we can push the proper boost, safely. He's also going to ACTUALLY tune the car with my SCT chip. To help the engine compartment look more presentable, we're also going to remove all the ugly emissions and install a coil over plug setup to get rid of plug wires. I'm excited to finally get it back and running the way I hoped last time.

Be careful who you trust out there, people. There really are some unethical people that just guess their way through life... I'll keep the name anonymous, as I'm not the type of person to dime them out in public. I will say, go with your gut. If something doesn't feel right, RUN! I should have, but didn't... Uggghhhhh
 
You must log in or register to reply here.

Similar threads

Progress Thread Giving an abandoned 88 GT project a new chance at life
  • jaketractor
  • Jan 9, 2025
  • Fox 5.0 Mustang Tech
  • 2
Replies
27
Views
2K
Fox 5.0 Mustang Tech Jul 20, 2025
Noobz347
J
2000 GT Idle/Running Issues
  • junkman306
  • May 11, 2020
  • SN95 4.6L Mustang Tech
Replies
6
Views
3K
SN95 4.6L Mustang Tech May 15, 2020
junkman306
J
R
  • Locked
SOLD 1996 Mustang Gt Convertible Pi Swapped
  • RedFord96
  • Mar 2, 2016
  • SN95 Mustangs For Sale (1994-04)
Replies
0
Views
2K
SN95 Mustangs For Sale (1994-04) Mar 2, 2016
RedFord96
R
S
  • Locked
Expired Fs: '03 Ysi Built Gt Project, 44k Miles, Clean Title..
  • svtlightning01
  • Jun 19, 2014
  • SN95 Mustangs For Sale (1994-04)
Replies
0
Views
2K
SN95 Mustangs For Sale (1994-04) Jun 19, 2014
svtlightning01
S
  • Locked
SOLD 96-04 2v Intercooled Vortech Setup Includes Power Pipe/b.o.v/mafs Flange....etc
  • musclemustangcb
  • Sep 23, 2012
  • Engine and Power Adder Parts
Replies
5
Views
2K
Engine and Power Adder Parts Oct 7, 2012
musclemustangcb
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SN95 4.6L Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?