292 Y BLOCK...........
- Thread starter A67StangMaster
- Start date
A67StangMaster said:
Where in San Jose is this guy? His name isn't Butch is it? When I went to look at my first car with my dad, we went into this shop just behind Independence High School and this guy had cars upon cars in there. I looked over in the corner and there were 2 Shelby GT500's sitting side by side. If memory services me, there was only about 15000 miles on each and they were started and let run for 30 minutes every week. I asked if I could have one of those, the guy just kind of chuckled and gave the "Uh, no" answer. He was saving them for his grandkids.. Little bastards.... I did end up with an old Willy's Jeep though. That day started 2 obsessions, Jeeps and Mustangs.
bnickel said:
AAAAAAHHH!!! SACRELIGE!!! Cheby paint on a Classic Ford motor?
65ShelbyClone
Founding Member
BornInAFord said:The Ys are heavy, though, and are as large and heavy as a 429.
I haven't weighed the 292 my old man has sitting in his yard, but it is nowhere near the size of a 385 series. It's not even as big as a Cleveland....maybe a 351W.......I'm pretty sure anyway. I'm going to have to break down and get some size comparison pictures for all the engines between us. I have a 289, (built)302, and a 351W; he has a (built)390, 292, and 351C. Everything but the 390 and 302 is junk, unfortunately.
I wouldn't mind rebuilding the 292 and putting in either his '42 Ford dumptruck or building a '50s style slingshot dragster for it.
It is an original 4bbl engine out of a '57 Custom 300 and AFAIK, never been bored.292 y-block
Hi I came across your thread on the 292y-block, Do you still have the motor I know its been awhile since it was posted, I am looking for the 292 for a restore I. am doing.
Hi I came across your thread on the 292y-block, Do you still have the motor I know its been awhile since it was posted, I am looking for the 292 for a restore I. am doing.
If it is a truck 292, it should have a forged crank and would be very desirable for a vintage racer. Check for casting lines on the crank (narrow = stock, wide = forged). Y-blocks, especially stock bore ones are desirable for those restoring 1st gen T-birds and other Fords. The Ys are heavy, though, and are as large and heavy as a 429.
Daniel
I've never heard of these engines having steel cranks and as far as one being as big as a 429, they're closer in size to a small block Chevy. They're downfall was the stacked intake ports.........................................And now that I've studied this thread more, it's almost as old as a Y-Block..................
I've never heard of these engines having steel cranks and as far as one being as big as a 429, they're closer in size to a small block Chevy. They're downfall was the stacked intake ports.........................................And now that I've studied this thread more, it's almost as old as a Y-Block..................
i have heard that the trucks got forged cranks as well. also either the 292 or 312 crank makes a great crank to use as a stroker crank for a 289/302 block, that's what the reacer used to stroke a SBF before the proliferation of aftermarket stroker cranks......
i have heard that the trucks got forged cranks as well. also either the 292 or 312 crank makes a great crank to use as a stroker crank for a 289/302 block, that's what the reacer used to stroke a SBF before the proliferation of aftermarket stroker cranks......
I haven't had much experience with the Y blocks, so you could be right about that. I do recall the bore spacing was carried over to the small blocks, along with the journal diameters. That would definately prove that these engines were no where near the size of the 385 series motors.
yeah it's not as big as a 385 series but it does weigh almost as much, that weren't no thin wall casting block that's for damn sure
