3" Tailpipes installed!

1slow95 · May 6, 2008

I finally got around to ordering some tailpipes for my car. The only 3" pipes I could find were from Flowmaster and designed for a Fox. I read online that they would fit, and what do you know they actually fit!! It took me a while to get them installed, but it was definitely worth it. It sounds sooo much better now. My car is almost quiet now! Inside the car, at least.

I still need to do a little work to make it fit just right. One side sticks out farther than the other side. And my mufflers need adjusted up. I just about didn't make it back into my garage because the mufflers are too low now.

Here's a few pics. I'll get some better ones tomorrow when it's light out. And I might even get a short video.

fiveoho · May 7, 2008

man, that looks great. love the bends and tips.

whats that part # ?

1slow95 · May 7, 2008

http://store.summitracing.com/partd...400238+4294748485+4294908331+115&autoview=sku

Flowmaster 15820.

94GTLaserRC · May 7, 2008

Subscribing...That looks HOT!!

RC

1slow95 · May 7, 2008

Here's a couple blurry pics. I'll get some better ones after I get the pipes straightened out and the car cleaned up. I was too tired after work tonight to do anything with it.

94GTCoupe · May 7, 2008

those look damn good

95cbr331 · May 7, 2008

Good to see that they fit, I too just got the same tailpipes. What all has it taken to get them to fit? And also have you found any 3"intermediate pipes or did you get them made?

94GTLaserRC · May 7, 2008

IM digging the meat on those back tires!!
RC

1slow95 · May 7, 2008

I'm using a universal Kooks x-pipe. I had the mufflers mounted too far back, so I had to cut about 2" off my mid pipe. I also had to cut about 1/2" off the tailpipes where they connect to the mufflers. It's a very tight fit. I may need to do a little more cutting to get them exactly where I want them, but I'm going to see if I can just move everything around first.

96stangRC · May 8, 2008

nice!! I have the same ones just sitting in the box waiting to get welded on. Do the tips rub against the bumper or is it just the angle of the picture?

SMOKEDYA · May 8, 2008

Low-5.0 said:
I'm using a universal Kooks x-pipe. I had the mufflers mounted too far back, so I had to cut about 2" off my mid pipe. I also had to cut about 1/2" off the tailpipes where they connect to the mufflers. It's a very tight fit. I may need to do a little more cutting to get them exactly where I want them, but I'm going to see if I can just move everything around first.

Hey were you running at the NMRA event last year at national trails in aug? I either seen your car run there or somewhere maybe it was just parked in the lot? I remember the plate. Do you have the 408 in this car? Man i want to trade my SSP coupe for another S/N95 sooooo bad! peace

john

Blackened302 · May 8, 2008

they look great, Miz! perfet size, too.

94GTLaserRC · May 9, 2008

96stangRC said:
nice!! I have the same ones just sitting in the box waiting to get welded on. Do the tips rub against the bumper or is it just the angle of the picture?

ANOTHER RC

RC

96stangRC · May 9, 2008

haha RC FTW

Killercanary · May 9, 2008

Damn! I didn't go with 3" tail pipes because I couldn't find any and secondly I didn't think that they would fit with 315's out back. It looks like you have ample clearance with the tire too. Nice job!

1slow95 · May 9, 2008

SMOKEDYA said:
Hey were you running at the NMRA event last year at national trails in aug? I either seen your car run there or somewhere maybe it was just parked in the lot? I remember the plate. Do you have the 408 in this car? Man i want to trade my SSP coupe for another S/N95 sooooo bad! peace

john

Yep I was there. I did both the car show and bracket racing that weekend. And it's 418, not 408. ....Well, technically 420ci since it's .040 over instead of .030

The tailpipes do rub on the bumper right now. I'm going to try to readjust them as soon as I can.

Paul, I was really worried about tire clearance when I ordered these. A friend of mine has the MAC 3" pipes with 315's and they had plenty of clearance so I went ahead and took a chance on these. As you can tell I do have plenty of clearance around the tires.

BlackVert · May 9, 2008

i decided to go with mufflers that are 3" in and 2 1/2" out to quiet it down a little more and help with fitment concerns over the axle and out. but i have the dreaded drone and it is getting on my nerves, so i'll have to revisit my exhaust again ...

mike, what's the latest on the other end of your exhaust system? still moving away from the kooks?

1slow95 · May 9, 2008

BlackVert said:
mike, what's the latest on the other end of your exhaust system? still moving away from the kooks?

I don't know what I'm doing now. I want to drive it some more like this before I decide what I'm doing with the headers. I only drove it about 5 minutes or so the other night. I didn't really notice any exhaust leaks in that time, so I must have fixed it at some point and didn't notice because the car was so loud.

For the ground clearance issue, I've been wanting coil-overs for a couple years now. It might be time to go ahead and buy them. The other problem is the O2 sensors, which can easily be moved to one of the primary tubes.

1slow95 · May 9, 2008

I think I got it finished up tonight. The mufflers are in there nice and tight now. Unfortunately I couldn't get the driver side to fit exactly right, so it's still a little shorter and touching the bumper. But I did get the pass side almost perfect. I haven't drove it like this yet, so I'll wait until after the first test drive before I officially say it's finished.

Here's a short video for you guys. It's still cold here, it idles a little better once it's warmed up.

http://www.youtube.com/watch?v=2GeYlvysDTc

94GTLaserRC · May 9, 2008

Low-5.0 said:
I think I got it finished up tonight. The mufflers are in there nice and tight now. Unfortunately I couldn't get the driver side to fit exactly right, so it's still a little shorter and touching the bumper. But I did get the pass side almost perfect. I haven't drove it like this yet, so I'll wait until after the first test drive before I officially say it's finished.

Here's a short video for you guys. It's still cold here, it idles a little better once it's warmed up.

http://www.youtube.com/watch?v=2GeYlvysDTc

Joined.....1 hr ago...WELCOME To YOUTUBE!!!

RC

3" Tailpipes installed!

1slow95

fiveoho

1slow95

94GTLaserRC

Squint as you approach, lest you be blinded by my

1slow95

94GTCoupe

95cbr331

New Member

94GTLaserRC

Squint as you approach, lest you be blinded by my

1slow95

96stangRC

New Member

SMOKEDYA

Blackened302

Active Member

94GTLaserRC

Squint as you approach, lest you be blinded by my

96stangRC

New Member

Killercanary

The car that set the bar.

1slow95

BlackVert

1slow95

1slow95

94GTLaserRC

Squint as you approach, lest you be blinded by my

Similar threads

3" Tailpipes installed!

Squint as you approach, lest you be blinded by my

New Member

Squint as you approach, lest you be blinded by my

New Member

Active Member

Squint as you approach, lest you be blinded by my

New Member

The car that set the bar.

Squint as you approach, lest you be blinded by my

Similar threads

Privacy & Transparency

Privacy & Transparency