331 Supercharged...?

NewStangOwnr · Dec 3, 2007

Hey there all,

I found out the knocking noise is my rod, or something inside the motor..

Christmas is coming up and winter, so I have an excuse to do it then. I want to do a 331 and some form of forced induction. I would like to CnC the stock heads, new valve springs and rockers, and a new carb. Then the stroker and blower.

Any ideas to make the most power? I'm hoping for 500 or so? Achieveable?

Thanks for all the help!

classic boost · Dec 3, 2007

don't waste your money on cnc'ing the stock heads.

TOM B · Dec 3, 2007

You bet, the first thing I would NOT do is cc the old heads, go buy some Edelbrock or AFR heads, these and other head will flow much better than a stock cc'd head and you need that.

NewStangOwnr · Dec 3, 2007

ok, say I go with AFRs or Edelbrock, what would be a good size? I want to be able to run 89 Octane too, so how does a 10:1 cr sound?

Thanks!

rbohm · Dec 3, 2007

for heads use one of these;

the world products windsor jr

the performer rpm

the afr 185's

these all have similar port sizes, and flow about the same amount of air, and have similar valve sizes. by the way the wp heads are also available in aluminum if that is important to you. they all have 58-60 cc chambers and with flattop pistons will deliver about 9.5:1 compression which is the most you want to run ont he street with a supercharger, and you want to keep the boost below 10psi, especially if you want to use 89 octane lighter fluid. i also highly recommend using a boost referenced timing retard system.

TOM B · Dec 3, 2007

IM RUNNING 15 PSI ON MY 347.
I will be adding a methenol kit to cool the charge.

NewStangOwnr · Dec 3, 2007

TOM B said:
IM RUNNING 15 PSI ON MY 347.
I will be adding a methenol kit to cool the charge.

Specs? How much power are you making?

red65 · Dec 4, 2007

Point of reference -- I'm making 445rwhp, 427ft-lb rwt on a 306 with EFI and a Novi 1000 running about 9 psi. Assuming 15% drivetrain losses, that's over 520 at the flywheel.

That's on Holley Systemax heads. Previous advice is good - ditch the stock heads. There are lots of options available and it's a place to get good bang for the buck.

10secgoal · Dec 4, 2007

Just keep it 302 with a stock block and spend the money somewhere else ( like a good set of heads ). A stroker needs about a 15cc dish with 60cc to be close to 9-1.Flats top will put you close or well over 10-1 with 60cc heads, depending on the gaskets. 500 is pretty easy with boost.

NewStangOwnr · Dec 4, 2007

I see what your saying. I want to be able to run low boost and then up the boost and dump in race fuel for the track or the weekend.

How much is achievable with stock 302 and a supercharger?

iskwezm · Dec 4, 2007

10secgoal said:
500 is pretty easy with boost.

Is it now

10secgoal · Dec 4, 2007

NewStangOwnr said:
I see what your saying. I want to be able to run low boost and then up the boost and dump in race fuel for the track or the weekend.

How much is achievable with stock 302 and a supercharger?

Some go a while with 500 rwhp, some make 450fwhp and blow it. It really dependant on many things like how high you spin it, and most importantly the tune. A member here makes 477rwhp on pump gas, and tons of people make even more than that.

NewStangOwnr · Dec 4, 2007

Say I go with the 331 and some form of supercharger...Can I up the boost for the weekend and pump out 600hp? Will it last I mean?

10secgoal · Dec 4, 2007

You could turn up the boost and make 600 with either stroke, but it won't last at that power level with a 302 block. More feasible with a 351 at that point.

red65 · Dec 5, 2007

NewStangOwnr said:
Say I go with the 331 and some form of supercharger...Can I up the boost for the weekend and pump out 600hp? Will it last I mean?

Short answer: no. Anecdotally, the 5.0 block seems like it's good for ~400-450HP at the flywheel fairly reliably; much over that and the clock starts ticking. It ticks pretty fast at 600HP, I'd think.

NewStangOwnr · Dec 5, 2007

Say I have a 302 with 4 bolt main, will that even last?

I'm trying to avoid getting another block because I just got this one haha.

iskwezm · Dec 5, 2007

NewStangOwnr said:
Say I have a 302 with 4 bolt main, will that even last?

I'm trying to avoid getting another block because I just got this one haha.

i think the only 4 bolt mains are aftermarket and they are $$$$$$$$$$

NewStangOwnr · Dec 5, 2007

I thought there was a way to adapt 4 bolt mains, guess I read wrong. Hm.

Well. In that case...Uh...crap.

Will 4 bolt mains and a girdle make a big difference in the amount it can handle?

iskwezm · Dec 6, 2007

NewStangOwnr said:
I thought there was a way to adapt 4 bolt mains, guess I read wrong. Hm.

Well. In that case...Uh...crap.

Will 4 bolt mains and a girdle make a big difference in the amount it can handle?

A girdle is a band aid, it MIGHT save the rotating assembly from further damage, and yes i do have one

NewStangOwnr · Dec 6, 2007

What about 4 bolt mains? Help alot?

331 Supercharged...?

NewStangOwnr

New Member

classic boost

TOM B

NewStangOwnr

New Member

rbohm

TOM B

NewStangOwnr

New Member

red65

Member

10secgoal

Active Member

NewStangOwnr

New Member

iskwezm

10secgoal

Active Member

NewStangOwnr

New Member

10secgoal

Active Member

red65

Member

NewStangOwnr

New Member

iskwezm

NewStangOwnr

New Member

iskwezm

NewStangOwnr

New Member

Similar threads

331 Supercharged...?

New Member

New Member

New Member

Member

Active Member

New Member

Active Member

New Member

Active Member

Member

New Member

New Member

New Member

Similar threads

Privacy & Transparency

Privacy & Transparency