351 vs 302

undercnstrction

New Member
Nov 10, 2009
312
0
0
i'm sure this topic has been on here many times but i'm apparenlty not searching for it correctly.

i'm currently tearing down my '87 GT. i had pretty much decided to stick with the 302 and throw some bolt ons at it for good measure. but i just read a post from 90LXcoupe that really got me thinking about doing a 351 swap instead of rebuilding the 302. my BIGGEST concern is that car has to pass smog. but i would think if i used a late model engine from a pickup that wouldn't be an issue??? i haven't done any research yet to see what those motors produce out of the box but it can't be any worse than a stock 302. my car is a speed density system. will that affect the swap? are 351s just as cheap to rebuild as 302. i'm not after a high HP motor.........right now........but the 351 would leave that door WIDE open for a future build. are there aftermarket parts available for these motors as well? can any of you guys shed light on this thought process and tell me the pros and cons of going this route. i just bought an explorer upper/lower intake last night but i'll gladly resell it if my idea of going to a 351 is a valid and sound idea. would i need a different tranny setup(currently have a z-rated t-5, and centerforce clutch)? driveline issues, engine bay issues? i've noticed that most of you have gone the route of thumper 302s and i'm sure there is a reason for that instead of dropping in the 351s? HEEEELLLLPPPPPP! :shrug:
 
There is no real disadvantage to going with a 351 over a 302 other than hood clearance. The 351 is bigger, stronger, and with aluminum heads, the weight is not really a concern. Most of the parts are interchangeable between the two engines, so yes, there is a lot of aftermarket support for the big Windsor.

If you reuse all stock parts (H/C/I), don't expect the car to be a screamer. If you do go with aftermarket H/C/I, remember that 302 parts make 302 power.

Check out this thread for info on the swap:

http://www.stangnet.com/mustang-forums/589036-i-need-very-specific-website.html
 
I love my 357. I built YEARS ago, 1995. It has old parts on it, still has a GT40 intake which I know is killing power, the B cam which is fine for now. It has great torque where you spend 90% of the time driving...1500-3500 rpm's.
It has ran like a top for over 10 years/20,000 miles. It's a 1969 block, won't clear a factory hood, but when it's time to make some serious power...I have the proper foundation.
 
There is no real disadvantage to going with a 351 over a 302 other than hood clearance. The 351 is bigger, stronger, and with aluminum heads, the weight is not really a concern. Most of the parts are interchangeable between the two engines, so yes, there is a lot of aftermarket support for the big Windsor.

If you reuse all stock parts (H/C/I), don't expect the car to be a screamer. If you do go with aftermarket H/C/I, remember that 302 parts make 302 power.

Check out this thread for info on the swap:

http://www.stangnet.com/mustang-forums/589036-i-need-very-specific-website.html

THANX for that link!!!! i have not read through it yet but did scroll through it and HOLY SCHNIKE there's a ton of info there!

if the 302 aftermarket parts will fit a 351 you guys could have just made up my mind on which way i will be going.
 
I love my 357. I built YEARS ago, 1995. It has old parts on it, still has a GT40 intake which I know is killing power, the B cam which is fine for now. It has great torque where you spend 90% of the time driving...1500-3500 rpm's.
It has ran like a top for over 10 years/20,000 miles. It's a 1969 block, won't clear a factory hood, but when it's time to make some serious power...I have the proper foundation.


is the "357" the result of the standard rebuild....like a 302 going to a 306? i'm liking this idea more and more all the time.
 
Honestly, I'm not really sure why more people don't do it. They make more power when done right, and are much stronger, they are quite a bit heavier though. It is difficult to make it fit under a stock hood but it can be done. The same heads can be used as you would for a 302. If you get a roller 351 the same cam will work too. If it's an older non roller block you can retrofit it to use a roller cam. The lower intake is different (wider) because of the taller deck height. Obviously everything in the bottom end is different as well.
 
i think roller blocks happend in 1994, not 100% sure on that.

Honestly, if i knew what i know now, i would have built myself a 357 or 408, saved some money and made more power. All aftermarket 302 heads will bolt right up, so will the cams, your just gonna need a different dist and intake. If you order the right cam, emissions shouldnt be a problem. What state do you live in? and what test do you need to pass? is it visual, or a dyno test?
 
i really appreciate all of the input......although now i'm getting a head because i don't know which way to go. i printed off the info from the details of doing a 351 swap. i think it ended up being 15 pages of info!! now i got stuff to read while i'm on the crapper....LOL.....

90LXcoupe, to answer your question i live in vegas. the way they do the sniffer test (at least on the mustang) run the car up to about 2500-2800rpm and stick this gizmo into the tailpipe. let it run for several minutes then tell you if you passed or failed......well, i should say, they charge you $25 THEN tell you if you passed or failed.

i haven't read through all of the stuff from the different links you guys have posted, but what happens to all of the sensors and things that are on there now.....like the oxygen sensors, idle sensors, smog pump, etc etc? and the computer and speed density setup? does all of that need to be changed as well? from what i'm told, i can pick up a complete motor from the local scrap yard for $250. i haven't confirmed this yet but the price don't seem too bad.
 
i really appreciate all of the input......although now i'm getting a head because i don't know which way to go. i printed off the info from the details of doing a 351 swap. i think it ended up being 15 pages of info!! now i got stuff to read while i'm on the crapper....LOL.....

90LXcoupe, to answer your question i live in vegas. the way they do the sniffer test (at least on the mustang) run the car up to about 2500-2800rpm and stick this gizmo into the tailpipe. let it run for several minutes then tell you if you passed or failed......well, i should say, they charge you $25 THEN tell you if you passed or failed.

i haven't read through all of the stuff from the different links you guys have posted, but what happens to all of the sensors and things that are on there now.....like the oxygen sensors, idle sensors, smog pump, etc etc? and the computer and speed density setup? does all of that need to be changed as well? from what i'm told, i can pick up a complete motor from the local scrap yard for $250. i haven't confirmed this yet but the price don't seem too bad.

Here is a list of parts you will need that are 351w spacific.Dizzy,lower intake, oil pan and pick up,351w swap headers. IF you use 302 heads you need to drill the head bolts out 1/2" instead of 7/16th.All the stock sencers MAF TB water pump will work off the 302.Like OP said the cam from a 302 will work.MAKE SURE WHEN YOU GET THE CAM ORDER IT TO THE NEW FIRING ORDER if not then you will need to repin the ECM.When you order the dizzy make sure to get a EFI dizzy. Whatever year 351w you decide to get take all the acc. stuff with it and you should be ok.If you dont go to BIG on the cam as long as you run cats i bet you will pass DEQ without a smog pump or EGR.Also if you get an older or none EFI 351w you will need the fuel pump block off plate.You will probably need to move up to 24# injectors for a stock 351w and go to 42#"s for a mild built 351w.If you go with 24# injectors a diffrent MAF for 24's will be fine. If you go larger on the injectors you will need a chip and tune. peace











john:p
 
would it be worth the time and effort to find a lightning motor or just run with a motor out of a pickup or van? i'm going to try and stick with something '94 or newer since there is no difference in price from the local salvage yard. $250 out the door, and if i can score it quick enough the accessories come with it. after reading through the material you guys posted links to, it sounds like a pretty complicated process to get all of the odds and ends just right but it should be worth it in the end.

at this point, i would definitely be going with a very mild build so it sounds like the 24s would be the way to go. when i switch over to the 351 will that automatically eliminate my speed density system or will i have to change something there as well?
 
its should be easy to pass vegas smog, i do it every year lol.

one question i have is every once ive seen that has gone 351w went to a carb setup as well. Im like the OP, I have speed density and am thinging of a 351 in my future as well ( with boost ).
 
First thing to consider (since I don't see it stated anywhere) is your location? If you're in California, it doesn't matter how mild mannered you choose to build that 351W, the car is not going to pass the smog test with anything but the original engine in there.

They will never know! I bet 1/2 or over 1/2 the people on here or a normal joe schmo caint tell a 351w and a 302 apart if there sitting side by side?????Every single person that see's my engine at the track thinks it's a 302 or a 5.0!They never know it's a 351 till i tell them,then they say oh B.S i thought the 351's were bigger!peace











john:p