• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

5.0 Compression test & head gasket question

  • Thread starter Thread starter chepsk8
  • Start date Start date May 10, 2006

chepsk8

Founding Member
Jan 15, 2001
2,203
3
49
Easton, PA
May 10, 2006
#1
  • May 10, 2006
  • #1
I have a Factory Five Cobra Replia with a 1988 5.0 converted to carb. Radiator is a new 3-row, with a 16" electric fan. I have had an coolant loss problem for a while. Last year, I pulled the intake, and found ripped gaskets by the front coolant cross-over, and brown foam on the PCV & intake. Once this was fixed, the problem went away. After open-tracking the car a few days back, did I have problems again.

Here's where I stand:


OK, ran the cylinders last night with the intake off.

Cylinders 2,3,4,5,6,7 were all 155 to 165 (Not bad for 200K+ miles!)
#8 was 145-150
#1 was 140-145

After each test, I let the guage sit for 5 minites to see if there was any pressure drop. Only #1 very, very slowly lost 3 lbs during that time, but I could not hear any hissing or gurgling noise.

A visual inspection showed the following:

Spark plugs show no iron depisits, just the car running rich.
My Moroso "T" is still intact, and not leaking
All intake manifold gaskets intact & not broken
PCV valve clean, no brown foam
Underside of intake clean, no brown foam.
The only thing I did not get to was opening the oil drain plug to check for water, but it seems unlikely.

So, based on the above, I have two thoughts:

#1 - I just had too much advanced timing in it, not enough coolant, the coolant was mostly water, my catch tank allowed air to be pulled into the cooling system, and my location for the temp gauge was in the wrong spot(rear of manifold). Put it back together with the temp gauge up front, make sure it's full of good coolant, and go on my way.


or


#2 - I remember hearing somewhere that 5.0's to kill head gaskets in the forward cylinders (#1 & #8) where the water jacket is, and mine could only have a very small opening, but enough to cause my problems.

What's your take?


Many, many thanks from an old Classics guy!:SNSign:
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
May 10, 2006
#2
  • May 10, 2006
  • #2
With the compression readings you have, I would not suspect head gasket problems.

Fox box 5.0's have a air dam located below & in front of the radiator. It isn't anything more that a 3" piece of stiff plastic that is as wide as the radiator. It does help direct the airflow into the radiator. I don't know if FFV's use the same scheme, but you might want to look back at the kit plans.

Electric fans:
Electric fans need either a fan shroud that covers the backside of the radiator, or need to be mounted flush to the core with no gaps. The reason is that the fan should suck air through the radiator and not from the gaps between it and the core.
 

chepsk8

Founding Member
Jan 15, 2001
2,203
3
49
Easton, PA
May 10, 2006
#3
  • May 10, 2006
  • #3
I would think since the nose is fully ducted to the radiator, it creates a "ram" for the radiator. Also, I did put the fan in the Mustang shroud, and it keeps it cool while sitting.

If indeed I did have a head gasket issue, what would my typical readings be, and how fast would my pressure drop?
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
May 10, 2006
#4
  • May 10, 2006
  • #4
Blown head gaskets will give 25-75 PSI max pressure. The pressure would not hold at all.

If you have any doubt about the head gaskets, see the link in my sig. One of the tech notes on my website is how to build your own blow down compression tester. It puts regulated air pressure in the cylinders and measures the pressure drop.
 

chepsk8

Founding Member
Jan 15, 2001
2,203
3
49
Easton, PA
May 10, 2006
#5
  • May 10, 2006
  • #5
Many Thanks for your help!

In your opinion, would my heating up on the track be a result of low coolant & too much timing advance (I do not know exactly, but with a Unilite Dist w/no vac advance, I think I am somewhere about 15 degrees btdc), and the result of just beating it?
 

rd

Founding Member
Jan 12, 2000
3,316
63
109
Ocean Springs MS
May 10, 2006
#6
  • May 10, 2006
  • #6
I would suspect a low coolant problem first.

Is the car set up so that the top of the radiator or filler is at or below the level of the engine, specifcally the thermostat housiing.

If so, it may be hard to completely fill the system. It may take several triies, or a vacuum fill.

My Capri did this a while back, would run hot, etc. It leaks a good bit over a couple months, and does not get run much these days. A ten mile drive finally burped the air out and its been fine for several weeks, idles ok with the ac on. I usually fill it two or 3 times, dead cold, with the cap off, until the thermostat opens. Its worked this way for 25 years and 260k miles over 3 engines.

On a stock 5.0 car, any of the myriad hoses can weep at the connections, and cause a slow loss of coolant. My particular issue is the splice I have in one of the the heater hoses.
 
You must log in or register to reply here.

Similar threads

X
Engine 5.0 Head Gaskets installed wrong block coolant passages???
  • Xam Sirrah
  • Jul 21, 2025
  • Fox 5.0 Mustang Tech
Replies
12
Views
959
Fox 5.0 Mustang Tech Dec 22, 2025
Qtrhrse23
Engine New factory manifold no start
  • Fishnchips
  • Oct 15, 2026
  • 1994 - 1995 Specific Tech
Replies
13
Views
418
1994 - 1995 Specific Tech Oct 22, 2026
DadLife0724
F
Fox 1990 Mustang GT 5.0 A9L – Engine suddenly shuts off but immediately restarts when key turned
  • FishermansFriend
  • Aug 9, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
16
Views
695
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 30, 2026
General karthief
Engine Re-torquing intake manifold bolts question
  • 91GTstroked
  • Feb 22, 2025
  • Fox 5.0 Mustang Tech
Replies
6
Views
1K
Fox 5.0 Mustang Tech Mar 1, 2025
Jarhead67
J
D
Engine Questions on compression test results
  • dqureshi06
  • Jan 6, 2025
  • Fox 5.0 Mustang Tech
Replies
5
Views
580
Fox 5.0 Mustang Tech Jan 7, 2025
Noobz347
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?