• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

87 GT Keeps Starting

  • Thread starter Thread starter SilverSER
  • Start date Start date Mar 18, 2006
S

SilverSER

New Member
Feb 17, 2006
8
0
0
Mar 18, 2006
#1
  • Mar 18, 2006
  • #1
I bought an 87 GT a little over a month ago and it hasn't given me any problems until now. I thought I knew how to fix it but apparently I don't and I’m running out of money and patience so maybe you guys could help me out a little!

A week or two after buying the car the starter wouldn't turn the engine over on the first and sometimes a second try. I went on ahead and bought an Optima Red battery and the problem magically went away for a day! The next day it started doing the same thing. This time I replaced the starter Solenoid. All was great for about 3 days until a different problem arose. I started the car up and the starter kept running once the engine was started. After stalling the car I disconnected the battery but once I attached it back it kept doing the same thing. I took a voltmeter to the solenoid and noticed that it was stuck together. This time around I installed a new starter, starter cable and my second new Solenoid. It ran great twice then the starter kept running again and the Solenoid was stuck shut again. I’m starting to get aggravated that I can’t pin-point the problem. Anyone have any ideas?

Thanks in advance! :SNSign:
 
7

795.0

New Member
Dec 30, 2005
76
0
0
Mar 19, 2006
#2
  • Mar 19, 2006
  • #2
Unfortunately, I don't have an answer to your problem, but I can offer a few things that I would check.
Get a wiring diagram for your car. Trace the wires going to the soleniod, and the ignition switch. Make sure none are out of place. Make sure there aren't any wires from the run and start circits that are shorting together.
Disconnect the cable going from the solenoid to the starter to keep from damaging the flywheel. Just attach a test light to the output side of the soleniod to check if it's still sticking.
You've already replaced what I would suspect to be causing the problem. At this point, I would really think it would be something in the ignition switch, or between the start / run circuits.
 
M

Mike92GT

Founding Member
Jan 23, 2002
583
0
0
Florida
Mar 19, 2006
#3
  • Mar 19, 2006
  • #3
Just a thought, but you might want to check the ignition switch on the steering column and the connector that goes to it. The switches have a tendency to get hot and short themselves out. Looked for burn spots or melting inside the switch and connector. You'll have to remove some trim pieces and dash panels to get to it.
 
M

Mike92GT

Founding Member
Jan 23, 2002
583
0
0
Florida
Mar 19, 2006
#4
  • Mar 19, 2006
  • #4
Oops, I just saw 795.0 suggested the same thing at the end of his post.
 
S

SilverSER

New Member
Feb 17, 2006
8
0
0
Mar 19, 2006
#5
  • Mar 19, 2006
  • #5
Thanks guys, time to go give it a try!
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Mar 19, 2006
#6
  • Mar 19, 2006
  • #6
Good advice above. The White/pink (IIRC) wire is the crank wire at the ignition switch (if inspecting it).

I would also caution that starting or attempting to start a car with a lack of battery amperage can cause the solenoid contacts to latch.

I might try a Ford solenoid and see how it does.

Good luck.
 

Bad92GT

The 5 Minute Plan Man
Jun 10, 2004
492
0
0
SC
Mar 19, 2006
#7
  • Mar 19, 2006
  • #7
how about the starter itself.. the battery and all that you replaced could have just made it work for a few more times.. i'd go after a starter..
 
B

BaXTeR3221

Member
Jan 12, 2004
917
0
16
Orange County, NY
Mar 19, 2006
#8
  • Mar 19, 2006
  • #8
I think he already replaced the starter. I agree with the other that taking a look at your ignition is a good place to start.
 

JBeezy53

Member
Dec 28, 2003
559
1
19
Sacramento, Ca
Mar 19, 2006
#9
  • Mar 19, 2006
  • #9
That happen to me before. In my case it was a bad starter, but I don't think thats your problem considering yours was new.
 
S

SilverSER

New Member
Feb 17, 2006
8
0
0
Mar 19, 2006
#10
  • Mar 19, 2006
  • #10
Well I took all of the plastic dash off around the steering wheel. I looked at the wiring harness that has the starter wire in it. The majority of the plastic part of it looks warped from overheating and some of the wires have a lot of corrosion on them. It looks like this is my problem after all. I also tried to open the rest of the ignition but it’s held shut with tamper proof torx screws (either 25 or 27?) and NAPA can’t get the socket in until Tuesday. So where’s a good place to buy a new wiring harness? Thanks again guys! :SNSign:
 
S

SilverSER

New Member
Feb 17, 2006
8
0
0
Mar 19, 2006
#11
  • Mar 19, 2006
  • #11
ttt
 
M

Mike92GT

Founding Member
Jan 23, 2002
583
0
0
Florida
Mar 19, 2006
#12
  • Mar 19, 2006
  • #12
I would try Ford first. The ignition switches had a recall a while back. When I still worked there you could get a wiring repair kit, connector and switches, and they were usually in stock due to the recall. A lot of times you could just pop the wires out of the old connector one by one and re-install them in a new connector.
 

Tonys96Cobra

professional deer "mounter"
Oct 28, 2005
19
9
29
Syracuse
Mar 19, 2006
#13
  • Mar 19, 2006
  • #13
Mike92GT said:
I would try Ford first. The ignition switches had a recall a while back. When I still worked there you could get a wiring repair kit, connector and switches, and they were usually in stock due to the recall. A lot of times you could just pop the wires out of the old connector one by one and re-install them in a new connector.
Click to expand...
Yeah, i lost a 91 GT due to the ignition switch recall, that they did not inform me of. Burned down in the parking lot at work
 
S

SilverSER

New Member
Feb 17, 2006
8
0
0
Mar 19, 2006
#14
  • Mar 19, 2006
  • #14
Tonys89GT said:
Yeah, i lost a 91 GT due to the ignition switch recall, that they did not inform me of. Burned down in the parking lot at work
Click to expand...

I thought about that happening but I was lucky enough to have the quick disconnect battery cables, since of course the car wouldn't break down in the driveway and I had to run home and get some tools.

Thanks for the recall tip! I'll head up there in the morning.
 
You must log in or register to reply here.

Similar threads

C
Electrical HELP! 1989 5.0 Stick, Voltage Bleed onto Ignition Trigger wire
  • ChickenDeluxe
  • May 14, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
405
Fox 5.0 Mustang Tech May 24, 2026
ChickenDeluxe
C
A
1987 5.0 speed density Foxbody crank no start
  • Alan2204
  • May 23, 2026
  • Fox 5.0 Mustang Tech
Replies
10
Views
598
Fox 5.0 Mustang Tech May 30, 2026
Mcmahst
T
Electrical 1990 Vert starting/Solenoid issues
  • Tom77
  • Apr 18, 2025
  • Fox 5.0 Mustang Tech
Replies
6
Views
522
Fox 5.0 Mustang Tech Apr 18, 2025
85GTStangGuy
M
2004 v8 convertible
  • Mikeycrownvicluver
  • Feb 12, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
11
Views
599
1996 - 2004 SN95 Mustang -General/Talk- Feb 15, 2026
Mikeycrownvicluver
M
8
Electrical Crank-no start ... no spark ... no injector pulse, was it something I did? (redux)
  • 85gtCOBRA
  • Oct 28, 2025
  • Fox 5.0 Mustang Tech
Replies
2
Views
688
Fox 5.0 Mustang Tech Oct 29, 2025
85gtCOBRA
8
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?