• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

93 GT to 94/95 6/4 cylinder conversion

  • Thread starter Thread starter samuraichamploo
  • Start date Start date Sep 4, 2004

samuraichamploo

Member
Mar 18, 2004
367
0
16
Beaumont, TX
Sep 4, 2004
#1
  • Sep 4, 2004
  • #1
93 GT W/ 351w to SN95 6 cylinder conversion

I have a built engine and tranny. everything has less than 300 miles on it.
I had plans on fixing the thousand things wrong with my exterior/interior but I am thinking I would like to just buy a 6 cyl sn95 and throw my engine and tranny in there. The reason I will be putting it all into a 6 cyl sn95 instead of a GT model is because I just dont have the cash. A 4/6 cyl sn95 with a blown engine or with high miles can be found for under 4k.
So if I had a complete *running* (daily driver) 93 mustang gt vert with a 351, how hard would it be to get it into the sn95?????
also, it might be noteworthy to mention I have a 351 in there, not a 302...

for all the uber verterans, this topic has not been covered before as far as I can search.
 

samuraichamploo

Member
Mar 18, 2004
367
0
16
Beaumont, TX
Sep 4, 2004
#2
  • Sep 4, 2004
  • #2
also, what about putting it into a SHO tauras?
 

hllon4whls

BANNED
Founding Member
Jan 17, 2002
2,567
0
46
Covington
Sep 4, 2004
#3
  • Sep 4, 2004
  • #3
The taurus is front wheel drive transversly mounted V6. It will be next to impossible to mount it front wheel drive. Rear Wheel drive is possible, but still going to be very difficult. It will require many fabrication skills, a big budget or possibly both.

As far as a 351 into an SN95, you need basically all the things covered to drop into a fox including a new diff. Cost might be a wash. Buy car, rear diff, engine brackets misc VS buy brackets, dime a dozen interior pieces, etc.
 

samuraichamploo

Member
Mar 18, 2004
367
0
16
Beaumont, TX
Sep 4, 2004
#4
  • Sep 4, 2004
  • #4
Hey man, I got the swap all done as you can see... You should check it out.. runs like a mofo..
You wouldnt happen to need any 1.72 roller rockers or a holley 750 DP carb would you? Well I have both for sale so lemme know
 
You must log in or register to reply here.

Similar threads

A
2001 Mustang GT, scorched metal smell and noise from trans/diff?
  • AndyE2255
  • Dec 1, 2025
  • SN95 4.6L Mustang Tech
Replies
4
Views
467
SN95 4.6L Mustang Tech Dec 28, 2025
gkomo
K
1994 mustang GT 50
  • Kimberly45
  • Nov 14, 2024
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
4
Views
405
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Nov 15, 2024
General karthief
A
95 Gt intermittent backfire
  • A_A_Ron
  • May 26, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
0
Views
429
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- May 26, 2025
A_A_Ron
A
K
Engine 93 gt new 351 w moter put in and installing ace's kill shot EFI. It turns over but Wan't start? Need Help.
  • kimscales
  • Jun 1, 2024
  • Fox 5.0 Mustang Tech
Replies
1
Views
1K
Fox 5.0 Mustang Tech Jun 2, 2024
AeroCoupe
Brakes ‘93 Cobra Brake Booster and Master Cylinder Question
  • Willybill32
  • Jun 28, 2023
  • Fox 5.0 Mustang Tech
Replies
13
Views
3K
Fox 5.0 Mustang Tech Jun 30, 2023
Willybill32
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?