• Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-

96 pats help

  • Thread starter Thread starter Cobralove
  • Start date Start date Nov 11, 2018
  • Tags Tags
    1996 pats pats issue
C

Cobralove

New Member
Nov 11, 2018
9
0
1
New York
Nov 11, 2018
#1
  • Nov 11, 2018
  • #1
Hello Stangfam,

I have a 1996 cobra. Running and functioning perfectly fine. My pats transceiver (black plastic ring with wire running under driver side dash and connects via a white plastic head ) broke near the black plastic ring part that goes onto ignition cylinder. Now the theft light blinks rapidly and will not allow me to start the car. I have got a used Oem Pats transceiver and am ready to install it. Will it be as simple as slapping the functioning pats transceiver on and throwing out the old one that broke?? Any and all information will help a lot!
 

Attachments

  • CBCAA132-D93C-4718-83E8-2E6161607D31.webp
    41.9 KB · Views: 1,765

wmburns

SN Certified Technician
Aug 14, 2009
5,892
514
204
Houston Texas
Nov 11, 2018
#2
  • Nov 11, 2018
  • #2
Cobralove said:
Will it be as simple as slapping the functioning pats transceiver on and throwing out the old one that broke??
Click to expand...
Yes.

>>>from 1996 Ford manual.
Transceiver

Removal
  1. Remove ignition switch lock cylinder (11582) from steering column housing. Refer to Section 11-04 .
  2. Remove screw retaining passive anti-theft transceiver module to steering column lock cylinder housing (3511).
  3. NOTE: Only apply pressure or leverage below the key cylinder lower rib.

    Locate rib on steering column lock cylinder housing, using a small screwdriver gently pry passive anti-theft transceiver module over the rib.
  4. Disconnect passive anti-theft transceiver module from steering column locators and wiring harness connector.
 
C

Cobralove

New Member
Nov 11, 2018
9
0
1
New York
Nov 12, 2018
#3
  • Nov 12, 2018
  • #3
wmburns said:
Yes.

>>>from 1996 Ford manual.
Transceiver

Removal
  1. Remove ignition switch lock cylinder (11582) from steering column housing. Refer to Section 11-04 .
  2. Remove screw retaining passive anti-theft transceiver module to steering column lock cylinder housing (3511).
  3. NOTE: Only apply pressure or leverage below the key cylinder lower rib.

    Locate rib on steering column lock cylinder housing, using a small screwdriver gently pry passive anti-theft transceiver module over the rib.
  4. Disconnect passive anti-theft transceiver module from steering column locators and wiring harness connector.
Click to expand...

Thank You! Will I have to reprogram the keys I already have for the car ? By doing the “put ket to on(run) position and off a few times to reprogram it?
 
C

Cobralove

New Member
Nov 11, 2018
9
0
1
New York
Nov 12, 2018
#4
  • Nov 12, 2018
  • #4
Such as what is posted here
https://mustangforums.com/forum/4-6l-1996-2004-modular-mustang/573325-how-to-program-a-pats-key.html
 

wmburns

SN Certified Technician
Aug 14, 2009
5,892
514
204
Houston Texas
Nov 12, 2018
#5
  • Nov 12, 2018
  • #5
You asked a question. "is it as SIMPLE as replacing the broken part" to which I replied "Yes".

If PATS needed to be reprogrammed, then:
  • It would not be a "simple" job. A major OBTW such as necessary reprogramming should be mentioned.
  • there would have been a mention of the need to reprogram PATS in the Ford service manual snip that was included.
Don't over think this. Think of the PATS transceiver as a radio antenna. This is not the same as changing the chip key, the cluster, or the PCM.
 
C

Cobralove

New Member
Nov 11, 2018
9
0
1
New York
Nov 14, 2018
#6
  • Nov 14, 2018
  • #6
wmburns said:
You asked a question. "is it as SIMPLE as replacing the broken part" to which I replied "Yes".

If PATS needed to be reprogrammed, then:
  • It would not be a "simple" job. A major OBTW such as necessary reprogramming should be mentioned.
  • there would have been a mention of the need to reprogram PATS in the Ford service manual snip that was included.
Don't over think this. Think of the PATS transceiver as a radio antenna. This is not the same as changing the chip key, the cluster, or the PCM.
Click to expand...


Thank you very much for the assistance, really appreciate you taking the time.
 
S

shadowherder

New Member
May 17, 2020
1
0
1
sudbury ontario
May 17, 2020
#7
  • May 17, 2020
  • #7
If you broke your halo ring there is a away is you take it apart there is a ribbon with 3 prongs that goes to the ring. If you broke the ring off you can (i used) some speaker wire or whatever and i wrapped my key with a couple winds with the wire, one end of the speaker wire I spilt so it touched 2 prongs then the other end wire to the far end prong, On the transceiver board where the ribbon plugs into there is a little arrow on the little black receiver thats the side I plugged the singe end to.
No more flashing theft light.
 
You must log in or register to reply here.

Similar threads

B
Resolved 1996 PATS help needed
  • Bajaboy
  • May 21, 2025
  • SN95 4.6L Mustang Tech
Replies
5
Views
501
SN95 4.6L Mustang Tech May 23, 2025
Bajaboy
B
0
V6 to V8 Swap info
  • 02_2v_Curtis
  • Jan 11, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
0
Views
576
1996 - 2004 SN95 Mustang -General/Talk- Jan 11, 2026
02_2v_Curtis
0
SURGING IDLE / NO IDLE CHECKLIST FOR 1996–1998 MUSTANG GT (4.6L 2V) - Work In Progress
  • Noobz347
  • Aug 30, 2025
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
0
Views
664
1996 - 2004 SN95 Mustang -General/Talk- Aug 30, 2025
Noobz347
D
Electrical Manual 2003 GT 4.6L coupe that will not start. Thoughts? Resources?
  • DapperFish
  • Jan 17, 2024
  • SN95 4.6L Mustang Tech
Replies
3
Views
1K
SN95 4.6L Mustang Tech Jan 22, 2024
PSKSAM2
P
PATS Issues on Engine Swap
  • 1978Cobra2
  • Jan 28, 2020
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • 2
Replies
21
Views
9K
1996 - 2004 SN95 Mustang -General/Talk- Feb 4, 2020
1978Cobra2
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?