• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

AFR 165 supplies

  • Thread starter Thread starter 2012 Mustang GT
  • Start date Start date Jul 26, 2005
  • 1
  • 2
Next
1 of 2 Next Last

2012 Mustang GT

Member
Jun 5, 2004
94
0
6
Alger,Michigan
Jul 26, 2005
#1
  • Jul 26, 2005
  • #1
What kind of stuff is needed to bolt up AFR 165 heads to my car, do the heads come with everything on them?

can someone please tell me what i would need to buy if i was just gonna swap the stock heads with AFR 165 heads?

and is stud mounted better than pedestal?

thanks for your help
 
L

luckythirteen13

New Member
Jul 19, 2005
648
0
0
Anaheim, CA
Jul 26, 2005
#2
  • Jul 26, 2005
  • #2
stud mount is much better then pedistal, its stronger.
you will need roller rockers, hardened push rods, and depending on your mods/future plans, id get 24# injectors, recalibrate maf for the larger injectors and a larger fuel pump.'
if you still are using the stock cam, nows the time to put in a performance cam. you will never see the afr's potential with a stock cam so while the engine is torn down to the block, you might as well do the cam now. if you do a cam, youll want a new timing chain too.
now with all this going in (cam or not) you will need a way to tune your a/f ratio cause its going to be way off. if you dont have a wide band o2 kit, nows a good time to get one or take it to a dyno tuner after the install. to adjust a/f ratio you will need an adjustable fuel pressure regulator.
you can easily pay $3000 in parts all at once (including heads, cam and tune)

do it right the first time, youll thank yourself in the end
 

2012 Mustang GT

Member
Jun 5, 2004
94
0
6
Alger,Michigan
Jul 26, 2005
#3
  • Jul 26, 2005
  • #3
thats exactly what i was looking for
thanks
 

Flavadave4

Active Member
Nov 28, 2003
1,044
21
49
Utica, NY
Jul 26, 2005
#4
  • Jul 26, 2005
  • #4
hey cool.....i was looking for simular help...thanks
 

Michael Yount

Mustang Master
Apr 10, 2002
9,039
6
79
Charlotte, NC
Jul 26, 2005
#5
  • Jul 26, 2005
  • #5
If you get the emissions-legal 165's, they can simply be bolted onto your stock engine. I'd want to replace the fasteners with ARP hardware - either new bolts or studs.

The AFR's will show a signficant gain even with the stock cam. Keep in mind when you start changing the cam (heart of the motor) you really need to think through the entire combo to optimize your results. There are lots of folks out there running aftermarket cams (and other parts) who make more power than stock, but also have an engine with very poor bottom end power - which doesn't make for a fun or efficient street car. So the place to start is knowing exactly how you intend to use the car and what you want out of your mods. Got to have that nailed down before you start picking parts.

Also, the 94/5 computers are MUCH more sensitive to changes than the 89-93's are, so the further from stock you go with your changes, the more likely it is you'll need to alter the ecu to get it to run well. Contrary to the other posters comments, AFR heads with a good intake and exhaust system and stock cam will TOTALLY wake up a stock-cammed motor and will not require any significant tuning for the ecu. The efi is mass-air -- it senses how much air is entering the engine and selects the appropriate amount of fuel to inject. So if the cam stays stock, you shouldn't require a chip or tuning other than timing changes. By the way, to capitalize on the AFR heads, I'd suggest an aftermarket intake (GT40, Cobra or Explorer will work well with the stock cam), and long tube headers with a free flowing exhaust system. Those changes will make a noticeable difference without negatively impacting drivability or fuel mileage if you can keep your foot out of it. Change the cam, and things get much more interesting in terms of drivability.

Good luck with it.
 

2012 Mustang GT

Member
Jun 5, 2004
94
0
6
Alger,Michigan
Jul 26, 2005
#6
  • Jul 26, 2005
  • #6
thanks, i guess i will do that and look into a cam and mess with the computer later.
 
L

luckythirteen13

New Member
Jul 19, 2005
648
0
0
Anaheim, CA
Jul 26, 2005
#7
  • Jul 26, 2005
  • #7
thats what i forgot, arp head bolts or studs. do not for any reason use the stock ones. depends on your mods, how your a/f will react to the heads. my stock fuel pump is completely maxed out. the best a/f ratio i could get with the stock pump was 26:1 because it just didnt flow enough fuel. had to put in a 255lph pump to keep up with demand, but every part of the engine that air and fuel touch from front to back is aftermarket (stock internals though) so my a/f ratio was about 30:1 after all the parts went in. the ecu controls the bottom end very well (with stock pump, idle was 13.5:1) with no tune needed, but the top end will more then likely need help.
 

2012 Mustang GT

Member
Jun 5, 2004
94
0
6
Alger,Michigan
Jul 26, 2005
#8
  • Jul 26, 2005
  • #8
so r u saying that i should get a new fuel pump?
 
L

luckythirteen13

New Member
Jul 19, 2005
648
0
0
Anaheim, CA
Jul 26, 2005
#9
  • Jul 26, 2005
  • #9
you could get away with not getting on right now since you will still have stock intake, maf and exhaust. you will need one down the line when you begin to get more air into the engine.
 

2012 Mustang GT

Member
Jun 5, 2004
94
0
6
Alger,Michigan
Jul 27, 2005
#10
  • Jul 27, 2005
  • #10
i have now decided to keep the stock cam for drivability reasons
what type of rockers should i get?
1.6 or 1.7
i really want this thing to sound good also and i know that a cam can change how it sounds
 

Michael Yount

Mustang Master
Apr 10, 2002
9,039
6
79
Charlotte, NC
Jul 27, 2005
#11
  • Jul 27, 2005
  • #11
I'd go with 1.7's if you're gonna change them - be sure you know which kind you want before you get your heads -- the 165's come in stud mount or pedestal mount - that will affect your rocker choices.
 

2012 Mustang GT

Member
Jun 5, 2004
94
0
6
Alger,Michigan
Jul 27, 2005
#12
  • Jul 27, 2005
  • #12
well i would like to get stud mount cuz they r stronger. what company would any of u suggest?
adn would i be able to reuse my stock valve covers?
 

tunedin302

I AM the law!!!
Jul 29, 2004
1,251
2
36
Pennsylvania
Jul 27, 2005
#13
  • Jul 27, 2005
  • #13
Per Rick91GT:

Scorpion rockers on AFR 165s
 

Dbeck002

New Member
Apr 30, 2005
710
0
0
South florida
Jul 27, 2005
#14
  • Jul 27, 2005
  • #14
94 Mustang GT said:
well i would like to get stud mount cuz they r stronger. what company would any of u suggest?
adn would i be able to reuse my stock valve covers?
Click to expand...


I hear scorpions are really good... You should be able to use the stock valve covers but there is only one way to find out.

Oh don't forget to get new dowels (small round metal objects that align the head to the block), these are a couple bucks at a local shop.


You'll also need thread SEALANT WITH TEFLON compound available at pep boys.
The sealant is used to seal the lower head bolts, those bolts actually penetrate into the water jackets so there must be a water tight seal at the threads.
Plenty of RTV Silicone
Get some carb/choke cleaner - good to degrease parts and get them ready to lube up with assembly lube
Assembly lube of course
New ARP headbolts (this is a must as mentioned before)
Plenty of time, if it takes you 2 weeks to do the project so be it. As long as she starts up the first time when youre done...

Good luck if you have any questions PM me im doing a headswap as well...
 

Michael Yount

Mustang Master
Apr 10, 2002
9,039
6
79
Charlotte, NC
Jul 27, 2005
#15
  • Jul 27, 2005
  • #15
I don't know of any roller rockers that will clear the stock covers without some mods. Most everyone has to remove the baffle in the oil filler tube. Many have to grind some of the structural ribs on the underside of the covers; some use double thickness valve cover gaskets. I bought a used set of Cobra valve covers -- took care of the problem.
 

Dbeck002

New Member
Apr 30, 2005
710
0
0
South florida
Jul 27, 2005
#16
  • Jul 27, 2005
  • #16
Michael Yount said:
I don't know of any roller rockers that will clear the stock covers without some mods. Most everyone has to remove the baffle in the oil filler tube. Many have to grind some of the structural ribs on the underside of the covers; some use double thickness valve cover gaskets. I bought a used set of Cobra valve covers -- took care of the problem.
Click to expand...

Do you have a pic by any chance? I wanna see what the cobras look like.
 

2012 Mustang GT

Member
Jun 5, 2004
94
0
6
Alger,Michigan
Jul 27, 2005
#17
  • Jul 27, 2005
  • #17
i herd somewhere that there is "tall" valve covers, r they for the bigger rockers?
would they fit under a gt-40 intake?
i know they would fit under a bbk one
 

Michael Yount

Mustang Master
Apr 10, 2002
9,039
6
79
Charlotte, NC
Jul 27, 2005
#18
  • Jul 27, 2005
  • #18
http://www.stangcity.com/showphoto.php/photo/2160/cat/500/page/2

Click on the link, and then click on the pic to enlarge; the pass. side is pretty clear - it's a simple stamped steel valve cover, with a small depression running down the middle. That's the 93 Cobra cover; the 94/5's had "cobra' in script stamped into the top. I'm a 'form follows function' guy -- fancy looking valve covers don't do much for me - as you can see.
 

Michael Yount

Mustang Master
Apr 10, 2002
9,039
6
79
Charlotte, NC
Jul 27, 2005
#19
  • Jul 27, 2005
  • #19
Many of the taller covers require the use of a 3/8" or 1" spacer between the upper and lower intake to provide clearance for the throttle body/cable. Which in some cars causes hood clearance issues...it's a vicious cycle.
 

2012 Mustang GT

Member
Jun 5, 2004
94
0
6
Alger,Michigan
Jul 27, 2005
#20
  • Jul 27, 2005
  • #20
so the cobra covers will work then without a spacer
?
 
  • 1
  • 2
Next
1 of 2 Next Last
You must log in or register to reply here.

Similar threads

K
Engine Gt40p vs 180 procomp
  • Kleinjj27
  • Oct 27, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
476
Fox 5.0 Mustang Tech Nov 3, 2026
Kleinjj27
K
Fox Xtremely high fuel consumption
  • PonyGTrider
  • Apr 11, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 9 10 11
Replies
213
Views
6K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- May 9, 2026
PonyGTrider
  • Locked
Engine Might have to get a Dart block but don't want to and if I do, then 363 instead of 331. Thoughts on what I've already bought so far.......
  • from6to8
  • Jul 8, 2025
  • Fox 5.0 Mustang Tech
Replies
2
Views
636
Fox 5.0 Mustang Tech Jul 8, 2025
Noobz347
Most ridiculous / dishonest work you have heard a shop recommend?
  • SchwarzStock
  • Jul 19, 2026
  • Off-Topic Hangout
Replies
4
Views
145
Off-Topic Hangout Jul 20, 2026
SchwarzStock
A
Discussion on mild budget build/ top end
  • Acesario
  • Feb 21, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
20
Views
1K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Feb 23, 2026
General karthief
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?