AOD TO T5 SWAP!! NEED SOME HELP!!!

Georgie · Mar 31, 2006

I GOT THIS ARTICLE ON THIS LINK FOR MY T5 SWAP...http://www.wcfords.com/articles/tech/t5swap/t5swap.html

THEIRS A PARTS LIST: BUT I DON'T KNOW WHAT PARTS I NEED TO BUY NEW AND WHAT PARTS I SHOULD GET AT A SCRAP YARD.. CAN SOMEONE HELP??

- Starter index plate
- Bell housing/scatter shield
- Pivot ball
- T5/T5Z transmission
- Shifter
- Shifter knob
- Shifter weather seal
- Shifter boot
- Flywheel
- Clutch kit (pressure plate, clutch disk, and throw out bearing)
- Pilot bearing
- Clutch fork
- Clutch cable
- Clutch cable clip (secures the cable to the bell housing)
- Pedal Assembly
- Clutch quadrant
- Speedometer gear
- Back-up light harness (Ford part# E7ZZ-15525-A)
- T5 transmission cross member
- Exhaust hanger

I KNOW WHERE TO GET THE CLUTCH KIT, FLYWHEEL,QUADRANT,CLUTCH CALE, SHIFTER , BOOT AND WEATHER SEAL AND BACK-UP LIGHT HARNESS... I ALREADY HAVE THE T5 WITH BELL HOUSING AND A FORK..HOW DO I KNOW IF THE FORK IS GOOD? WHATS A STARTER INDEX PLATE??SCATTER SHIELD? WHATS A PIVOT BALL??

ANY INFO WOULD BE GREAT HELP!!

GearHd6 · Apr 1, 2006

Clutch kit, Pilot Bearing, Throw Out Bearing and Aftermarket Quadrant should all be bought new.

SPEEDYLIFSAVR · Apr 1, 2006

The clutch fork is a pretty sturdy piece of metal , It should be ok as long as it is not obviously bent or distorted , just make sure it has the retaining clips for the pivot ball and TOB .

The starter index plate is a thin piece of metal that goes in between the block and bellhousing , Summitt has them .

The Scatter shield is the bellhousing .

The pivot ball looks like a bolt with a rounded top that screws into the bellhousing on the inside . The end of the clutch fork clips onto it and and allows it to pivot back and forth on the bearing retainer . If you get a used bellhousing it should be in there , if not let me know I got one laying around .

Georgie · Apr 4, 2006

WHATS A TOB?

Georgie · Apr 4, 2006

Georgie · Apr 4, 2006

CAN I USE THE STARTER INDEX PLATE FROM MY AUTO TRANSMISSION?>>?

5spd GT · Apr 4, 2006

TOB is a Throw-Out Bearing

Here is a link to the pivot ball:

http://www.latemodelrestoration.com/lrs.aspx?ref=mu&gotopage=/content_50_home.aspx

Georgie · Apr 4, 2006

THATS WHERE IM CHECKING FOR MOST OF MY PARTS.... THE LIBNK I POSTED BE4 FOR THE T5 SWAP DOESNT SAY ANYTHING ABOUT THE Tranny mount...do i need to get one??

BLK3DGT · Apr 4, 2006

AOD to T-5 swap

You will need a new crossmember and rear trans mount. the back up light harness is no longer available through Ford. You will have to wire it yourself, only two wires.
The spacer plate between the block and flywheel is different from an automatic and a stick. They are not expensive. The speedo gear assy should be the same so save that.

I am doing the same conversion on my Stang. Just take your time and get all the parts you need first. Do one step at a time, pedal assembly, remove console and auto shifter and locking cable. Then tackle the bottom end.

Good Luck!!:SNSign:

BLK3DGT

-ben- · Apr 5, 2006

I would just go get all the major parts first, i got mine off ebay. Transmission, bellhousing, etc... Crossmember and tranny mount from the auto will work-regardless of what many people say. I used the same ones and it worked fine. I bought my flywheel at summit racing-$99. Just about every bolt you can get from a parts store such as lowes, except for the pressure plate bolts, you will have to get them from a dealer. The clutch fork is the same as a 4cyl- i got mine from autozone. If you have at least a little idea of what your doing, it is very easy once you get started.

wht93gtEd · Apr 5, 2006

-ben- said:
...Crossmember and tranny mount from the auto will work-regardless of what many people say...

That, my friend, is a false statement. The AOD crossmember & the t5 are different.

However, I'll give you the benefit of the doubt, and say that the AOD crossmember can be modified (fairly easily) to work with the t5.

The AOD mounts farther back on the crossmember than the t5 does, so you'll have to grind off the welds where the crossmemeber meets the bushing tube things so you can slide the crossmember forward to align properly.

Also, you need a different slip yoke for your driveshaft. The driveshafts themselves are the same length, but the AOD uses a different yoke than the t5 does.

Georgie · Apr 5, 2006

ok i looked in my bellhousing that came wit the tranny.. the pivot ball is a little worn out.. can i still use it?

and my throw out bearing looks to be fine.. should i reuse it??

help me dude :SNSign:

Georgie · Apr 5, 2006

Georgie · Apr 5, 2006

and if i need to get a pivot ball..i onjly need one? and should i get the ajustable ones?

5spd GT · Apr 5, 2006

You need one pivot ball, and no-adjustable one. No need for that IMO with what you are setting up. It is just screw in...

Georgie · Apr 5, 2006

and what speedometer gear do i need.. speedo drive gears, or speedometer driven gears??? plus i cant find the starter index plate anywhere..summit only has them for auto tranny,,,,

5spd GT · Apr 5, 2006

Check 50resto again for the starter index plates...I would assume it has it?

The transmission will have the driven gear in it...

Depends on what gears you have...

wht93gtEd · Apr 6, 2006

and don't reuse the old TOB...it's cheap insurance to just get a new one.

Georgie · Apr 20, 2006

what speedometer gear do i need???

Georgie · Apr 20, 2006

AOD TO T5 SWAP!! NEED SOME HELP!!!

New Member

Member

New Member

New Member

New Member

"the 5.0 owns all"

New Member

Member

New Member

Active Member

New Member

New Member

New Member

"the 5.0 owns all"

New Member

"the 5.0 owns all"

Active Member

New Member

New Member

Similar threads

Privacy & Transparency

Privacy & Transparency