• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

B&M Supercooler Install!! Do i have it right???

  • Thread starter Thread starter Kdubslugga
  • Start date Start date Apr 15, 2006

Kdubslugga

Active Member
Jun 7, 2003
1,515
3
38
Akron, OH
Apr 15, 2006
#1
  • Apr 15, 2006
  • #1
Just wanna make sure i got this right. All i do is disconnect the return line from the original radiator cooler and put the fitting in that which is supplied by the kit. I run a hose from that to the new supercooler. Then run a hose from the line that i disconnected to the other post on the supercooler and im done correct??? Now the bottom line on the stock radiator cooler is the return line correct???? And also just to make sure, there is no need to even touch the supply line right. I want the stock cooler to cool it and then go to the Supercooler. Am i good??
 

bill302

Active Member
Nov 2, 2005
2,131
1
46
alabama,gadsden
Apr 15, 2006
#2
  • Apr 15, 2006
  • #2
yes thats the way i would run it. the fluid will enter the rad. cooler first then it will pass thru to the supercooler and the last line connected on supercooler will be the return, not the bottom line on the stock radiator cooler the fluid will enter at this point.
 

bill302

Active Member
Nov 2, 2005
2,131
1
46
alabama,gadsden
Apr 15, 2006
#3
  • Apr 15, 2006
  • #3
running the fluid thru the supercooler last after exiting radiator cooler will allow fluid to return to the tranny alot cooler than installing opposite just a little added info. to the post i posted above...
 

tunedin302

I AM the law!!!
Jul 29, 2004
1,251
2
36
Pennsylvania
Apr 15, 2006
#4
  • Apr 15, 2006
  • #4
That is the correct way to run a tranny cooler. Essentially, you are running it in series on the return line. Put the cooler in front of the radiator so the cooler fluid is being cooled first and not heating up the fluid in the stock portion of the radiator. Double check on which is the return line. Usually, the return line will have a fitting so a tranny flush can be done. Good luck.
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Apr 16, 2006
#5
  • Apr 16, 2006
  • #5
I agree with the in-series after the stock radiator's heat exchanger method. Some people (in frigid climates) like to recommend it backwards, but my take is:
If it's cold out, the stacked plate cooler is going to bypass till the fluid warms up (which your heat exchanger is helping with), so it's not unnecessarily cooling the fluid when the fluid is cold. A stacked plate cooler acts like it has a poor man's thermostat.

I think the AOD and AODE lines are backwards, which would mean the lower line is the return line. Dont go without checking. Loosen the line you think is the return line. Connect a fiting and hose to the radiator's heat exchanger and run the line into a bucket. Bump the starter or start it real quick and shut it down (fluid will fly out if you actually start it - but it might not come out if just cranking). If fluid comes out of the heat exchanger, goes into the ad hoc line you installed and ran to the bucket, that indicates you have the location. If the stock line spurts instead, you got the wrong line. This might all be in your instructions.

Also read up on preferences upon which way to flow fluid through the cooler. IIRC most folks like to have the fluid go into the bottom of the aux cooler and egress (back towards the trans) at the top of the new cooler.



Good luck.
 
You must log in or register to reply here.

Similar threads

M
Resolved 1988 Foxbody - Overheating Summer
  • MDrisc
  • Oct 26, 2025
  • Fox 5.0 Mustang Tech
Replies
16
Views
1K
Fox 5.0 Mustang Tech Jul 17, 2026
fasterthangas
F
A
Resolved Fuel pressure high at 52 new FPR same thing
  • afjLX
  • Dec 28, 2024
  • Fox 5.0 Mustang Tech
  • 3 4 5
Replies
90
Views
5K
Fox 5.0 Mustang Tech Jan 11, 2025
AeroCoupe
0
V6 to V8 Swap info
  • 02_2v_Curtis
  • Jan 11, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
2
Views
1K
1996 - 2004 SN95 Mustang -General/Talk- Oct 7, 2026
2v_johnny
2
A
Blow through intercooled questions
  • AngryH58
  • Aug 31, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
5
Views
293
1996 - 2004 SN95 Mustang -General/Talk- Sep 1, 2026
AngryH58
A
Forced Induction Bypass valve backwards?
  • Dontknowchit
  • Jun 25, 2025
  • Fox 5.0 Mustang Tech
Replies
3
Views
493
Fox 5.0 Mustang Tech Jun 29, 2025
JD1964
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?