• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Backfiring through intake??

  • Thread starter Thread starter Wicked_306
  • Start date Start date Jan 23, 2006
W

Wicked_306

New Member
Aug 14, 2005
45
0
0
Jan 23, 2006
#1
  • Jan 23, 2006
  • #1
Ok, I drove my car to work and back with no problems. It was just fine when i parked it and didn't drive it for a couple of days. Now at idle it backfires out of the intake about every 10-20 seconds. I didnt do anyting to it from the time I drove it before, It feels like it is running off of 6 cylinders, it has no power and even sounds different. I have no idea what it could be because I didnt do anything to it except install autometer gauges but that has nothing to do with it. Its a 306 with about 2000 miles, tfs stage one, kieth black dome tops, bolt on's ect...I havnt had any problems till now. Any help is appreciated. Thanks

PS The timing is set on 20 degrees where I have always ran this motor with no probs and I dont have a fuel pressure gauge, so I dont know what it is set at but I have a stock fuel pressure regulator on it.
 

srothfuss

Last night I stabbed the same guy 7 times in a row
Oct 17, 2004
1,796
3
0
Woodward Ave.
Jan 23, 2006
#2
  • Jan 23, 2006
  • #2
A trick to find out what cylinder is giving you problems:

With the motor off remove one of the plug wires off of the distributor. Start the motor. If it runs worse, that cylinder is functioning fine. Turn off the motor and move on to the next plug wire. Reconnect the previous wire before removing the next one to avoid confusion. Make your way around the entire distributor

*Remember to remove and install the plug wires with the motor off. You don't need to be getting an unnecesary shock.

You can also dump the codes pretty easy out of the computer (you only need a 2" piece of wire.) This will also do a cylinder balance test which is the easier method to the trick I posted above.

These methods will only tell you which cylinders are at fault.


Backfiring: When the intake valve on a cylinder is open too long and the combustion mixture is ignited. The ignited mixture then travels up into the intake looking for more oxygen. One or two of your cylinders have intake valves open too long. Or opening at the wrong time.
 

Dark Knight

Founding Member
Feb 1, 2000
2,578
0
0
Chandler, Az.
Jan 23, 2006
#3
  • Jan 23, 2006
  • #3
Sounds like an exhaust valve might have come loose.. check for arcing in the dist. too..
 
W

Wicked_306

New Member
Aug 14, 2005
45
0
0
Jan 23, 2006
#4
  • Jan 23, 2006
  • #4
Dark Knight said:
Sounds like an exhaust valve might have come loose.. check for arcing in the dist. too..
Click to expand...


What do you mean by come loose? The rocker arm? There is no knocking in the motor. This is so weird. Thanks
 

srothfuss

Last night I stabbed the same guy 7 times in a row
Oct 17, 2004
1,796
3
0
Woodward Ave.
Jan 23, 2006
#5
  • Jan 23, 2006
  • #5
Maybe he ment the intake valve? I'll wait for him to elaborate some more.
 

jadedinpa

Founding Member
Aug 2, 2002
1,094
0
0
lancaster, pa
Jan 23, 2006
#6
  • Jan 23, 2006
  • #6
i would say its a spark problem, like the TFI module is going out, or the pip sensor in the dizzy is getting flaky.

is it getting worse with time?
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Jan 23, 2006
#7
  • Jan 23, 2006
  • #7
Engine backfires:
1.) Excessively lean mixture. Look for vacuum leaks, low fuel pressure, dirty injectors or bad injector electrical power, EGR stuck open.
2.) Spark plug wires crossed or cross-firing.
3.) Sticking intake valve, bad valve spring, poorly adjusted valves.
4.) dirty or failed MAF sensor - look for code 66 when you dump the codes.

Use a vacuum gauge to look for sticking valves. The reading will be low (8"-14" @ 1200 RPM) and the needle will sweep every time the cylinder fires.

Use a fuel pressure gauge to tap the fuel pressure test point just behind the alternator. Measure the pressure with the engine idling, vacuum line off the fuel pressure regulator. You should see 38-40 PSI.

Do a cylinder balance test to isolate bad cylinders.
Cylinder balance test:
Warm the car's engine up to normal operating temperature. Use a jumper wire or paper clip to put the computer into test mode. Start the engine and let it go through the normal diagnostic tests, then quickly press the throttle to the floor. The engine RPM should exceed 2500 RPM's for a brief second. The engine RPM's will increase to about 1450-1600 RPM and hold steady. The engine will shut off power to each injector, one at a time. When it has sequenced through all 8 injectors, it will flash 99 for everything OK, or the number of the failing cylinder such as 22 for cylinder #2. Quickly pressing the throttle again up to 2500 RPM’s will cause the test to re-run with smaller qualifying figures. Do it a third time, and if the same cylinder shows up, the cylinder is weak and isn’t putting out power like it should. See the Chilton’s Shop manual for the complete test procedure

Here's the link to dump the computer codes with only a jumper wire or paper clip and the check engine light, or test light or voltmeter. I’ve used it for years, and it works great.

See http://www.troublecodes.net/Ford/
OR
See http://www.dalidesign.com/hbook/eectest.html for more descriptive help
OR
See http://www.mustangworks.com/articles...-iv_codes.html

For those who are intimidated by all the wires & connections, see http://www.actron.com/product_detail.php?pid=16153 for what a typical hand scanner looks like. Normal retail price is about $30 or so at Walmart.

Or for a nicer scanner see http://www.midwayautosupply.com/deta...ption.asp?3829 – It has a 3 digit LCD display so that you don’t have to count flashes or beeps.. Cost is $33.
 
W

Wicked_306

New Member
Aug 14, 2005
45
0
0
Jan 24, 2006
#8
  • Jan 24, 2006
  • #8
Thanks for the info. I'll get a scanner and check the cylinders. Thanks
 
M

mustang-a-holic

New Member
Jul 8, 2005
51
0
0
Jan 24, 2006
#9
  • Jan 24, 2006
  • #9
20 deg BTDC spout out? Seems high. This might indicate a timing chain problem or messed up damper

Original timing chain? Maybe stretched / hopped a link.

Back your timing back to stock see what happens. Check plugs. What do you see?
 
W

Wicked_306

New Member
Aug 14, 2005
45
0
0
Jan 24, 2006
#10
  • Jan 24, 2006
  • #10
mustang-a-holic said:
20 deg BTDC spout out? Seems high. This might indicate a timing chain problem or messed up damper

Original timing chain? Maybe stretched / hopped a link.

Back your timing back to stock see what happens. Check plugs. What do you see?
Click to expand...

Yes, I have ran it tuned like that since it was built. It is a stock timin chain. I have messed with the timing and it doesnt change the way it feels, feels like its got half the power it used to. All of the plugs looked like the cylinders were running lean except for # 7 and 8 cylinders were running rich? What could that mean? It just feels like something is totaly not tuned right on the car. Something happened from the last time I drove it because it was just fine then I parked it for a couple of days and put gauges in it and feels like it has half the power and feels like sh**. It runs really rough when trying to accelerate and will barely accelerate. If the distribiter was bad would it show up on the check engine light? Thanks
 

Realmongo

I prefer to be called "Evil Genius"
Founding Member
Oct 10, 2001
2,466
86
99
Western Mass
Jan 24, 2006
#11
  • Jan 24, 2006
  • #11
Sounds like a problem I had years ago when the timing chain jumped a tooth.
 
M

mustang-a-holic

New Member
Jul 8, 2005
51
0
0
Jan 24, 2006
#12
  • Jan 24, 2006
  • #12
Realmongo said:
Sounds like a problem I had years ago when the timing chain jumped a tooth.
Click to expand...


That's kind of where I'm leaning...
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Jan 25, 2006
#13
  • Jan 25, 2006
  • #13
Realmongo said:
Sounds like a problem I had years ago when the timing chain jumped a tooth.
Click to expand...
Roller chain drives will not jump a tooth. If there was that much slack, the engine wouldn't run.
 
W

Wicked_306

New Member
Aug 14, 2005
45
0
0
Jan 25, 2006
#14
  • Jan 25, 2006
  • #14
Hey guys. I found the problem. It was the coil. Thanks for your help.
 
You must log in or register to reply here.

Similar threads

T
Engine Need help figuring out misfire and backfire
  • trystancounts
  • Sep 25, 2025
  • Fox 5.0 Mustang Tech
Replies
8
Views
440
Fox 5.0 Mustang Tech Sep 26, 2025
Noobz347
1
Engine 91 mustang 302 Low acceleration car backfires pops and acts like it doesn’t want to take fuel
  • 1991Fox5.0
  • Oct 4, 2025
  • Fox 5.0 Mustang Tech
Replies
16
Views
1K
Fox 5.0 Mustang Tech Oct 6, 2025
1991Fox5.0
1
M
01 mustang 3.8 fuel pressure issue
  • Mhaley2006
  • May 29, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
4
Views
537
1996 - 2004 SN95 Mustang -General/Talk- Aug 9, 2026
JohnKay
J
Fox Xtremely high fuel consumption
  • PonyGTrider
  • Apr 11, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 9 10 11
Replies
213
Views
6K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- May 9, 2026
PonyGTrider
Engine Looking for suggestions and or ideas
  • PonyGTrider
  • Aug 25, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
726
Fox 5.0 Mustang Tech Sep 7, 2026
PonyGTrider
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?