• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Bad Tuning problem please help

  • Thread starter Thread starter kdropper1322
  • Start date Start date Aug 27, 2008
  • 1
  • 2
Next
1 of 2 Next Last
K

kdropper1322

New Member
Aug 27, 2008
10
0
0
Millbury, MA
Aug 27, 2008
#1
  • Aug 27, 2008
  • #1
i have a doozey for all of u and i am still sittin here befuddled at best. here's my scenario i have an 88 gt mustang trick flow twisted wedge heads, 1.6 rockers, f cam, 60lb injectors with a 60 maf to go with it, s trim supercharger from vortech with an anderson power pipe, also trick flow air intake, along with 75 throttle body and a bbk x pipe to boot. major tune problems to begin with the tune won't let me play with the fuel to air ratio and it won't let me by pass the timing of the car. i found top dead center and the car still won't run right it idles fine when cold as soon as temp hit's 100 degrees car stalls out and won't start any suggestions fixing this headache i heard it could be in the wiring harness but not sure?
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Aug 27, 2008
#2
  • Aug 27, 2008
  • #2
Dump the codes and see what the computer says is wrong…Codes may be present in the computer even if the Check Engine light isn’t on.

Here's the link to dump the computer codes with only a jumper wire or paper clip and the check engine light, or test light or voltmeter. I’ve used it for years, and it works great. You watch the flashing test lamp or Check Engine Light and count the flashes.

See Troublcodes.net Trouble Codes OBD & OBD2 Trouble Codes and Technical info & Tool Store. By BAT Auto Technical





If your car is an 86-88 stang, you'll have to use the test lamp or voltmeter method. There is no functional check engine light on the 86-88's except possibly the Cali Mass Air cars.



The STI has a gray connector shell and a white/red wire. It comes from the same bundle of wires as the self test connector.

89 through 95 cars have a working Check Engine light. Watch it instead of using a test lamp.



The STI has a gray connector shell and a white/red wire. It comes from the same bundle of wires as the self test connector.

There is a single dark brown connector with a black/orange wire. It is the 12 volt power to the under the hood light. Do not jumper it to the computer test connector. If you do, you will damage the computer.

What to expect:
You should get a code 11 (two single flashes in succession). This says that the computer's internal workings are OK, and that the wiring to put the computer into diagnostic mode is good. No code 11 and you have some wiring problems.

Codes have different answers if the engine is running from the answers that it has when the engine isn't running. It helps a lot to know if you had the engine running when you ran the test.

Trouble codes are either 2 digit or 3 digit, there are no cars that use both 2 digit codes and 3 digit codes.

Alternate methods:
For those who are intimidated by all the wires & connections, see Actron® for what a typical hand scanner looks like. Normal retail price is about $30 or so at AutoZone or Wal-Mart.

Or for a nicer scanner see EQUUS DIGITAL FORD CODE READER (3145) – It has a 3 digit LCD display so that you don’t have to count flashes or beeps.. Cost is $30.
 
K

kdropper1322

New Member
Aug 27, 2008
10
0
0
Millbury, MA
Aug 27, 2008
#3
  • Aug 27, 2008
  • #3
changed over

but i changed the car over from speed density to mass air so i changed out the computer and i believe that connection is not even used
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Aug 28, 2008
#4
  • Aug 28, 2008
  • #4
kdropper1322 said:
but i changed the car over from speed density to mass air so i changed out the computer and i believe that connection is not even used
Click to expand...

It is still used. All 5.0 Mustangs made between 86 and 95 used the same diagnostic connector and the same method to dump the codes. Even if you used a mass air conversion kit, the diagnostic connector still works the same.
 

strtrcr50

New Member
Jun 21, 2006
0
4
0
Previously from Dirty Jerzey exit 7a
Aug 28, 2008
#5
  • Aug 28, 2008
  • #5
kdropper, what are you using to tune the car?
 
K

kdropper1322

New Member
Aug 27, 2008
10
0
0
Millbury, MA
Aug 28, 2008
#6
  • Aug 28, 2008
  • #6
chip

im having dez racing do the tuning and it seems that we keep running into the same problem we are using a sct chip to tune it
 

vristang

15 Year Member
Mar 31, 2005
4,933
101
124
Seattle
Aug 28, 2008
#7
  • Aug 28, 2008
  • #7
What codes did you get?

What ecu do you have?


How are you trying to 'play with the afr' and 'bypass the timing'???

Why isn't your tuner working these issues for you??????????????????????????????
 
K

kdropper1322

New Member
Aug 27, 2008
10
0
0
Millbury, MA
Aug 29, 2008
#8
  • Aug 29, 2008
  • #8
issues

what i mean when i say bypass the timing is to advance it and he's been trying everything possible we are suppose to meet up sat so ill let you know how things shake out
 

04gtboy

New Member
Nov 27, 2005
83
0
0
Aug 29, 2008
#9
  • Aug 29, 2008
  • #9
A friend of mine just had his tuned . When they tried it wouldnt take his computer was bad . They used a sct chip on his to. Changed the computer and worked great!
 
K

kdropper1322

New Member
Aug 27, 2008
10
0
0
Millbury, MA
Aug 29, 2008
#10
  • Aug 29, 2008
  • #10
Computers

tried swapping the computers it was not the problem. checked all grounds too and that isn't the problem either kind of stuck at this point and suggestions would help
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Aug 29, 2008
#11
  • Aug 29, 2008
  • #11
kdropper1322 said:
tried swapping the computers it was not the problem. checked all grounds too and that isn't the problem either kind of stuck at this point and suggestions would help
Click to expand...

Surely you have a paper clip handy to dump the codes. This is the first step in troubleshooting 5.0 Mustangs.
 

vristang

15 Year Member
Mar 31, 2005
4,933
101
124
Seattle
Aug 29, 2008
#12
  • Aug 29, 2008
  • #12
This may come off as being rude, but that isn't the intention...

Why are you asking for help, if you aren't going to listen to the answers?

Pull the codes, and let us know what they are. JRichker is pretty good at getting these things straightened out.
You have not let us know what ecu you have.
What functions is the tuner trying to use to change Timing and AFR?

It's doubtful that this is a 'tuning' issue.
Most likely there is a failure in your system somewhere.

Take the time to properly diagnose the problem. Otherwise the best you can do is start buying new parts, which gets expensive.

Lastly,
Why isn't your tuner working this stuff out?
In my mind, this is part of what you pay him for... the expertise needed to sort out these issues.
 
K

kdropper1322

New Member
Aug 27, 2008
10
0
0
Millbury, MA
Aug 30, 2008
#13
  • Aug 30, 2008
  • #13
trying everything

well vristang that's just it he has been trying everything and we come down to it being something in the electrial system that isn't allowing us to tune the car at all so it when we do dump the codes i will let you know what i get for a reading and then maybe i can figure where to go from there
 

vristang

15 Year Member
Mar 31, 2005
4,933
101
124
Seattle
Aug 30, 2008
#14
  • Aug 30, 2008
  • #14
kdropper1322 said:
well vristang that's just it he has been trying everything and we come down to it being something in the electrial system that isn't allowing us to tune the car at all so it when we do dump the codes i will let you know what i get for a reading and then maybe i can figure where to go from there
Click to expand...
Again, not trying to be rude....

But telling us you have "tried everything" doesn't help us to help you.
What have you tried? Results?

Hopefully the tuner has already checked the codes... he should know to start with that.
 

vristang

15 Year Member
Mar 31, 2005
4,933
101
124
Seattle
Aug 30, 2008
#15
  • Aug 30, 2008
  • #15
kdropper1322 said:
as soon as temp hit's 100 degrees car stalls out and won't start
Click to expand...
ACT or ECT?
 
K

kdropper1322

New Member
Aug 27, 2008
10
0
0
Millbury, MA
Aug 30, 2008
#16
  • Aug 30, 2008
  • #16
here's what weve done so far

dump the codes nothing there. like i said before he thought maybe the timing was off tried that no dice. then we tried changing the computer itself that was not the problem same result with new computer. then we went with the grounding block is grounded to the fire wall and the injectors are grounded to the block nothing there. then we check the throttle position sensor and the mass air meter both in working order throttle position sensor is at .93 so that's not the problem. next up we tried the vacuum lines to make sure there's nothing going on. i have a brand new egr valve on the car so that's fine too. is there anything else i could try before changing out the harness?
 
K

kdropper1322

New Member
Aug 27, 2008
10
0
0
Millbury, MA
Aug 30, 2008
#17
  • Aug 30, 2008
  • #17
ect
 

vristang

15 Year Member
Mar 31, 2005
4,933
101
124
Seattle
Aug 30, 2008
#18
  • Aug 30, 2008
  • #18
kdropper1322 said:
dump the codes nothing there.
Click to expand...
As in you didn't get any codes?
or
You got code 11 for KOEO and KOER?
 
K

kdropper1322

New Member
Aug 27, 2008
10
0
0
Millbury, MA
Aug 31, 2008
#19
  • Aug 31, 2008
  • #19
i got the code 11 which means everything should be good
 

vristang

15 Year Member
Mar 31, 2005
4,933
101
124
Seattle
Aug 31, 2008
#20
  • Aug 31, 2008
  • #20
EDIT:
My first response was I was thinking of something else... sorry.


Will the car run without a chip/tune?


How well did the tuner clean off the J3 terminals?
 
  • 1
  • 2
Next
1 of 2 Next Last
You must log in or register to reply here.

Similar threads

Surging/stalling! problem or tune?
  • djj62478
  • Oct 4, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
11
Views
388
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Oct 14, 2026
KRUISR
D
N/A build on fresh stock 302
  • djcarrot
  • Oct 14, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
12
Views
442
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Oct 19, 2026
AeroCoupe
5
Hello Everyone !
  • 5150K
  • Jul 3, 2026
  • The Welcome Wagon
Replies
0
Views
186
The Welcome Wagon Jul 3, 2026
5150K
5
M
Engine Unexplainable Exhaust Pop and Gurgle
  • Mrnissen122
  • Feb 14, 2026
  • Fox 5.0 Mustang Tech
Replies
12
Views
837
Fox 5.0 Mustang Tech Feb 18, 2026
Noobz347
R
please help 87 mustang megasquirt 2 idle problems
  • robbie5.0
  • Jun 2, 2025
  • Digital Self-tuning Forum
Replies
2
Views
516
Digital Self-tuning Forum Jul 18, 2025
tate302
T
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?